blower not working with remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=48051
Printed Date: May 17, 2024 at 6:44 PM
Topic: blower not working with remote start
Posted By: pmes17
Subject: blower not working with remote start
Date Posted: January 18, 2005 at 8:40 PM
i have a compustar 2WASS and everything works great except when i trigger the remote start, the blower never kicks on until i put the key in the ign and put it to start. What wire did i put in the wrong place. The car is a 95 thunderbird. TIA
Replies:
Posted By: Craig3708
Date Posted: January 18, 2005 at 8:44 PM
Ignition #1: | | RED / LIGHT GREEN | IGNITION SWITCH HARNESS | Ignition #2: | | GRAY / YELLOW (# AWG) | IGNITION SWITCH HARNESS ** | Ignition #3: | | GRAY / YELLOW-2WIRES | IGNITION SWITCH HARNESS ** | Accessory: | | BLACK/ LIGHT GREEN |
If all these wires are powered up , everything should work fine. Craig
Posted By: BoominRolla
Date Posted: January 18, 2005 at 9:29 PM
Your definately not powering up an ACCESSORY! check again the wire you got is a BLACK/ light green that tests as positive with the key on then shuts off while cranking then goes positive again once the vehicles running -------------
Posted By: mo12v
Date Posted: January 18, 2005 at 10:00 PM
Ignition Switch Layout:
Starter..................RED / L BLUE.
Ignition #1..............RED / L GREEN (Primary Ignition).
Ignition #2..............GRAY / YELLOW (2) (Blower Motor) *
Ignition #3..............GRAY / YELLOW (Heat/Ac Controls).
Accessory................BLACK/ L GREEN (Radio/Wipers).
* 2 Of The 3 GRAY / YELLOW Wires Listed Are The Same Circuit. ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: pmes17
Date Posted: January 19, 2005 at 12:55 AM
all i konw is i have the Starter, Ign 1, and ign 2 hooked up ill have to look at the accessory and 3 ign tommarrow. Right now I Have the + Accesory to the gray / YELLOW. Which wire is the 2 ign and the 3 ign for the CM3000. The only thing im reading about is the 2 ign 200mA output. Please shed some light the car runs and starts fine right now except the blower kicking on and i have no way of telling if the radio works b/c theres no radio in the car right now.
Posted By: forbidden
Date Posted: January 21, 2005 at 12:55 PM
Meter all of the lines coming from the ignition cyclinder under normal key start. Figure out which ones are giving you power when the key is in and turned to on. Write down the color and status of each wire. Remote start the vehicle and do the same, compare the two. Once the unit is remote started, take a temporary jumper from the red or red / white +12 volt constant and jump it to the wire that did not match in the written comparison, chances are that this is your wire that is the acc. that needs to be powered up.
-------------
Top Secret, I can tell you but then my wife will kill me.
Posted By: leobito
Date Posted: January 21, 2005 at 2:30 PM
Re-Check your accesory wire !!
Posted By: kgerry
Date Posted: January 21, 2005 at 5:03 PM
i've done this before ... there are mulitple grey / YELLOW wires and you are not powering up the correct one... usually it's the thickest of the three that needs to be hooked up.....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
|