Help Installing Window roll up module
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=50238
Printed Date: June 04, 2024 at 12:00 AM
Topic: Help Installing Window roll up module
Posted By: Charming007
Subject: Help Installing Window roll up module
Date Posted: February 16, 2005 at 1:44 PM
I want to install a window control module to my 98 mustang GT. I got a window control module that has a 8 wires 1. for Left switch up 2. For left motor lead 3. For Right Motor switch up 4 For Right Motor lead 5 For Trigger 6. For Constant power (+) 7. For negative/ Ground (-) 8. For accesorry Item // I do not know where this one goes to where should I connect this to?? Also does it matter if it goes to a possitive (+) or Negative (-) wire?? If anyone know let me know thanks
Replies:
Posted By: xtreme069
Date Posted: February 17, 2005 at 3:31 AM
if this module is a 530t then wire 8 is supposed to be connected to an accessory output on your alarm which will allow the windows to roll down when the aux button is pressed if it is not then tell us the model of the window module and then we can go from there good luck!!
-------------
I Love This Industry!!
Posted By: xtreme069
Date Posted: February 17, 2005 at 3:35 AM
sorry i didn't read your meassage proparly wire 8 may be a shunt wire which gives out a negative pulse while the window rolls up so you can bypass a microwave or any other movement detector so the alarm doesn't activate when the windows are winding up
-------------
I Love This Industry!!
Posted By: silent1
Date Posted: February 23, 2005 at 5:14 PM
the window mod i just put in was run off the orange wire (grounded when armed), which rolled them up when armed and the acc wire on it was a pass through persay of that grounded wire. for starer kill...
-------------
Steve
Posted By: dar1
Date Posted: February 23, 2005 at 9:57 PM
First of all interface all the wires as you described. Interface each wire as notated. The best thing to do is obtain schematices for your vehicle wiring especially the door circuits. Then match up the module wires with the target wires in your vehicle curcuitry. Make sure to check and confirm for polarity with Multimeter.
-------------
one love
Posted By: Charming007
Date Posted: February 24, 2005 at 12:13 AM
I actually Think that the number 8 ACC WIre on my question above is there to make sure that the power control module does not activate when the car is on. The Trigger wire is the one that sends the negative pulse so that the windows can roll up. Can I delete this wire from my installation? Let me know if anyone knows.. Thanks for the replies.
Posted By: Charming007
Date Posted: February 24, 2005 at 12:17 AM
I actually Think that the "number 8" ACC WIre on my question above is there to make sure that the power window control module does not activate when the car is on. I want to hook it up to my power door locks to trigger the P.W.C.M. The Trigger wire is the one that sends the negative pulse so that the windows can roll up. Can I delete the acc wire from my installation? Let me know if anyone knows.. Thanks for the replies.
Posted By: jaurora
Date Posted: February 24, 2005 at 7:01 AM
What is the make and model number of the module. This will be all the help we would need.
-------------
MECP certified (If it really means anything)
Jeremy
Posted By: jmdomingos2
Date Posted: February 24, 2005 at 8:25 AM
you don't need the 8 wire, connect all others wires and job done. jorge -------------
Posted By: Charming007
Date Posted: February 24, 2005 at 3:09 PM
Thanks for the Replies, I do not know name or model# of The power window control module. It came in a little black box with the wiring diagram on it which is not that detailed and it is also on the Power control module itself. With The 8 Wires mention above in my question. Also does anyone know what exacltly the ACC Wire Does? Does it stop power when the Car is On? So that P.W.C.M does not activate when the car is on or on acc? I also read in this website that you can delete this wire. Thanks
Posted By: bretbowman
Date Posted: February 28, 2005 at 2:34 AM
This wire allows you to daisy chain multiple windows modules together by wiring the AUX input from the first window module to the alarm for input from your remote, then you can wire the ACC output to the AUX input of a second window module to controll the back windows., or a 529T (or other DEI or crimestopper window or sunroof module). Hope this helps! ------------- 2002 Toyota Sequoia Limited 2WD (Clifford G5 Avantguard 5 w/ 2 SmartWindows modules) - IT Engineer - NRA Life Member - LDS Return Missionary - Married for time AND ETERNITY - Eternally sealed family
|