96 neon, Hiteeh HT - 455
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=53872
Printed Date: May 07, 2024 at 11:05 AM
Topic: 96 neon, Hiteeh HT - 455
Posted By: rancidpunk
Subject: 96 neon, Hiteeh HT - 455
Date Posted: April 13, 2005 at 7:03 PM
Hey, I am installing an alarm system on my 96 neon, and im curious about a few things. 1. I have no power locks on my car, what to do with alarm wires? 2. Ths Relates to the first one, The Unlock/Lock wires and the - and + door switch, where do they go with no power locks and whats the difference. And to do with power unlock wire if i dont have one. 3. Finally theres 2 things, on is this site does not have the hazard lights description and my install guide has two white wires for it and does no say weither on is + or - , ok and theres also a wire for Engine Cap, ?What the hell is that, the oil cap? Someone please help it would be nice
Replies:
Posted By: swamprat323
Date Posted: April 13, 2005 at 8:11 PM
1. dotn do anythign with them. put power locks in sometime so u use them.
2. door "switch" connect to the door, only 1 of them not both, in your case it be the negtive one. cut the postive one out.
3. depending on alarm one of the parking lights will go to postive or negtive and the other to the parkign light in the, soem alarms have to parkign lights wires right and left. what make and modle of alarm do u have.
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|red & pink/black |+ |ignition harness *1 |
| STARTER|yellow |+ |ignition harness *1 |
| IGNITION|dk. blue |+ |ignition harness *1 |
| ACCESSORY|BLACK/ orange |+ |ignition harness *1 |
| POWER LOCK|ORANGE / purple |5wi|taped harness from driv door|
| POWER UNLOCK|pink/purple |5wi|taped harness from driv door|
| LOCK MOTOR|ORANGE / black | |drivers kick |
| UNLOCK MOTOR|pnk/wht or pnk/blk | |drivers kick |
| DISARM DEFEAT|pink/black | |passenger kick |
| PARKING LIGHTS +|BLACK / YELLOW | |at headlight switch |
| PARKING LIGHTS -| | | |
| HEADLIGHTS|lt. green |+ |at headlight switch |
| DOOR TRIGGER|yellow/black |- |behind headlight swtch |
| TRUNK/HATCH PIN|gray/black |- |at light in trunk |
| TACHOMETER|tan/blu or blk/gry | |top motor 3 pin plug |
| BRAKE WIRE|WHITE/ gold dots |+ |at brake switch |
| HORN TRIGGER|BLACK/ red |- |steering column |
| WIPERS|grn/yel, RED / yel |+ |steering column *2 |
| LF WINDOW UP/DN| | | |
| RF WINDOW UP/DN| | | |
| LR WINDOW UP/DN| | | |
| RR WINDOW UP/DN| | | |
Notes:
*1 SRS airbag wires are not enclosed in sheath at the steering column. They are a twisted pair run with rest of ignition harness. Be careful not to cut or probe these wires. *2 Combine with diodes to get all speeds.
Posted By: rancidpunk
Date Posted: April 13, 2005 at 9:06 PM
yah um my alarm is an "HiteCH Mobile Security HT - 455" um i dont have power locks and my alarm has the wires for it, so do i just ignore them. but still install the one door switch with or without power locks, right? also about the engine cap? theres a wire labelled for it and i dont know what it means, where its for, or if i even need it. thanks for the help so far. please help more though if possible
Posted By: rancidpunk
Date Posted: April 14, 2005 at 12:32 PM
hi ive understood most everything on my alarm install except for the relay system, i have made a diagram of it. i understand were the acc wire and the orange wires go, the 12v does it go to the battery or DC and where would i find dc in my car, yellow ignition coil i get, the only other thing is the switch connecting to the 12v and the acc and how i do this. please help thanks
Posted By: rancidpunk
Date Posted: April 14, 2005 at 12:37 PM
sorry pic didnt work first time let me try again 
Posted By: mo12v
Date Posted: April 14, 2005 at 5:27 PM
Is this for Ignition Kill or Remote Start??
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: dare_ds69
Date Posted: April 14, 2005 at 5:31 PM
what are you trying to do? what car is it?
-------------
how own your mind, control your life.
MECP certified. always use a DMM
Posted By: rancidpunk
Date Posted: April 14, 2005 at 6:42 PM
its for a dodge neon 1996 and im trying to set up the relay for the ignition for an alarm. the alarm is a HiTecH ht - 455. i just want to understand what the switch is and how to wire the damn thing
Posted By: mo12v
Date Posted: April 14, 2005 at 7:07 PM
If this is for Ignition Inhibit or "Kill" Ignition Kill will not work on ALL vehicles. U could send the wrong signal to computer and mess things up.
Starter Kill ( or Interrupt ) would be better. SPDT Relay
1 or 2 amp Diode across PIN 86 & PIN 85 with stripe facing PIN 86 Cut Starter wire in half: PIN 86 & 30 = Ignition switch half of cut wire
PIN 87a = Starter side of cut wire
PIN 85 = Negative Output from Alarm while Armed ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: swamprat323
Date Posted: April 15, 2005 at 8:09 AM
yes ignore the power lock wires.
yes install the one door switch, this will set off the alarm if door is open while the armed.
I dont know what the engine cap is and never heard of it. Dose it say were it connect too, or dose it have "any" other info. is ther a website form were you bought it, maybe they have the manurl up so i can see it.
Just skip that wire also, as long as the door, hood, and trunk is protected you should be fine. just tape the end of the wires your not useing so they cant touch anything by mistake.
Posted By: chay03
Date Posted: April 16, 2005 at 9:46 AM
Parking lights would go to BLACK / YELLOW wire behind light switch and is positive. It was a little difficult to cut the wire or tap into behind the switch, so I found the wire in the engine compartment, next to the battery in black loom bundle. That was just easier to tap into.
Posted By: philipk2003
Date Posted: April 26, 2005 at 1:36 PM
Engine cap for the Hitech 455 is the negative output for remote engine start. A module is needed for this function. Not sure why they called it "engine cap", but I think it has to do with some type of chinese to english translation.
Posted By: philipk2003
Date Posted: April 26, 2005 at 7:06 PM
Bobk, Not sure what to tell you, it is obviously that you are very knowledgeable based on your number of postings. (634 vs. my 1) However, I just installed one 2 days ago and I'm looking at the Owner's manual and wiring diagram as I type. Here is why I think it is an engine start module and why I think it is some type of chinese translation issue: 1) On page 7 and 8 the owners manual saids: " CH1 Output - Trunk Release (Option), CH2 Output - Power Window Roll Up (Option), CH3 Remote Engine Start (Option), CH4 - PW Roll Down (Option)". 2) Then on page 15 is the Wiring Diagram. There are only 4 optional output wire which are Trunk, roll up windows, ENGINE CAP, and Open Dormer (what ever Dormer is, I think is Open Window).
Posted By: philipk2003
Date Posted: April 27, 2005 at 5:00 PM
Have to disagree with you. The wiring diagram clearly states that it is a "O/P -500mA", that is OUTPUT (negative) 500 milliamps
Posted By: rancidpunk
Date Posted: May 26, 2005 at 5:45 PM
hi, i unfortantly have the gay htt-455 alarm, i know i should have spent more money but whatever, i thought i would give it a shot. i'v got almost everthing to work, except my when my alarm goes off do to the sensor the lights flash but there is no sound, is there anyone who would know why? also, after disarm my alarm or just entering the car period, all my lights flash for about 15s. i cant figure out why, if anyone could help me i would appreciate it alot, the car is a 96 neon sohc. ps if anyone needs help figuring out the relay i can tell you exactly what to do.
|