05 Kia sportage wire colors?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=55823
Printed Date: May 09, 2025 at 10:34 AM
Topic: 05 Kia sportage wire colors?
Posted By: Ren92
Subject: 05 Kia sportage wire colors?
Date Posted: May 16, 2005 at 10:41 AM
Does anybody have the wire colors for a 05' Kia sportage?
Replies:
Posted By: chungo
Date Posted: May 16, 2005 at 1:00 PM
12volts | white (30A), red (30A) | + | ignition harness | Starter | green | + | ignition harness | Second Starter | N/A | | | Ignition | blue | + | ignition harness | Second Ignition | N/A | | | Third Ignition | N/A | | | Accessory | orange | + | ignition harness | Second Accessory | pink | + | ignition harness | Keysense | WHITE/ orange | + | ign harn or ETACM, 22P plug, pin 10 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Power Lock | green | - | DKP or ETACM, 26 pin plug, pin 19 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Power Unlock | blue | - | DKP or ETACM, 26 pin plug, pin 21 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening.
To unlock the driver door only, use gray/orange (-) at the ETACM, 26 pin plug, pin 25. | Lock Motor | red | 5wi | driver kick, door harness | Unlock Motor | green | 5wi | driver kick, door harness | Parking Lights+ | green (L), green (R) | + | back of fuse box, 18 pin plug | Parking Lights- | brown | - | sw. or ETACM, 22 pin plug, pin 8 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Hazards | ORANGE / black | - | ETACM, 26 pin plug, pin 10 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Turn Signal(L) | blue | + | turn signal switch | Turn Signal(R) | green | + | turn signal switch | Reverse Light | white | + | back of fuse box, 18 pin plug | Door Trigger | orange | - | DKP or ETACM, 22 pin plug, pin 13 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Dome Supervision | brown | - | ETACM, 26 pin pug, pin 1 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Trunk/Hatch Pin | blue | - | DKP or ETACM, 22 pin plug, pin 14 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Hood Pin | white | - | sw. or ETACM, 22 pin plug, pin 15 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Trunk/Hatch Release | N/A | | | Power Sliding Door | N/A | | | Factory Alarm Arm | | | | Factory Alarm Disarm | | | | Disarm No Unlock | | | | Tachometer | blue | ac | cluster, 20 pin plug, pin 19 or ECM | Notes: The ECM (Engine Control Module) is on the driver side firewall, under the hood.
On the 2.0L, the tach wire is in pin 66.
On the 2.7L, the tach wire is in the 40 pin plug, pin 17.
Can also go to any fuel injector and use the wire that is NOT white. | Wait to start | N/A | | | Brake Wire | red | + | brake pedal switch | Parking Brake | blue/orange | - | sw. or ETACM, 22 pin plug, pin 17 | Notes: The ETACM (Electronic Time and Alarm Control Module) is in the center console, behind the radio and heater control opening. | Horn Trigger | blue | - | horn switch | Memory Seat 1 | N/A | | | Memory Seat 2 | N/A | | | Memory Seat 3 | N/A | | | Interface Module: | Category:
| Required: Yes | Type: Transponder | Part #: 556U or 555U | Notes: N/A |
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. |
|