programing the 555L

hi everyone ,  how are my pros doing today .  well i have a question .  i worked on a 2000 pontiac grand am 4 door .  i been tryin to make the remote start using the 555L  but it seems that the module is not reading the code . i bypassed the anti theft but the code resistance is not being readed by the 555L.  can anyone give me a tip on how to wire this particular set up . i really could use some its been breakiing my head. ohh can u guys tell me were i can locate the tach wire.  thanks guys anything helps.  sincerely Jose

12volts  red   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Starter  yellow   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Second Starter       Ignition  pink   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Second Ignition  dk. green   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Third Ignition       Accessory  orange   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Second Accessory  brown   +  ignition harness Notes: Remove the radio, without unplugging it, to access the ignition harness. Keysense       Power Lock  white   -  black plug in dkp Notes: Lock requires a negative trigger, and unlock requires a negative trigger through a 1,500 ohm resistor. Must use relays. Must close doors to lock with a single pulse. Power Unlock  same wire     Lock Motor  gray    drivers kick panel Unlock Motor  tan    drivers kick panel Parking Lights+  brown    passenger kick or column Parking Lights-       Hazards       Turn Signal(L)       Turn Signal(R)       Reverse Light       Door Trigger     -   Notes: The lt. GREEN/ black is located in the drivers kick and catches only the drivers door. The lt. blue is located in the harness coming from the drivers running board going under the drivers seat and it catches all other doors. Use both door trigger wires and diode isolate each. On the 2 door the lt.blue is in the passenger kick. Dome Supervision  white   -  dash light or column Trunk/Hatch Pin  ORANGE / black   -  trunk light Hood Pin       Trunk/Hatch Release  BLACK/ white   +  drivers kick panel Power Sliding Door       Factory Alarm Arm       Factory Alarm Disarm       Disarm No Unlock       Tachometer  white or PURPLE / wht    ignition coil or ECM Notes: The ECM is located under the left side of the dash to the left of the column. Wait to start       Brake Wire  lt. blue   +  at the switch Parking Brake       Horn Trigger  black   -  steering column Memory Seat 1       Memory Seat 2       Memory Seat 3       Interface Module: Category: Immobilizer Bypass Required: Yes Type: Passlock II Part #: 555LW Alternate Part1 #: 555T Notes: Interface Module: Category: Door Lock Interface Required: Yes Type: Multiplex Part #: 456LW Notes: Interface Module: Category: Combo Interface Required: Yes Type: Data Bus Part #: 457GW Notes: Can use the 457GW to bypass the Passlock II, but it will not control the door locks on this model year.

I dont know if there is a diffrence but in Directechs it says to use a 555lw. And the tach wire is white or PURPLE / white at the ignition coil or ECM. The ECM is located under the left side of the dash to the left of the column.

Luis

thanks for the help guys it really did help but i still have the same problem that when i remote start the car it will start and immediately shut down again can u guys tell why its doing this, i followed every step in order but still no posotive resuslts. thanks again u guys . 

jose

THANKS GUYS FOR THE HELP IM ALL SET I SIMPLY NEEDED TO LEARN THE TACH PROPERLY.  THAKN VERY MUCH FOR THIS JOB IS MY PASSSION, TAKE CARE KEEP POSTED.

lilchepe wrote:

---

THANKS GUYS FOR THE HELP IM ALL SET I SIMPLY NEEDED TO LEARN THE TACH PROPERLY. THAKN VERY MUCH FOR THIS JOB IS MY PASSSION, TAKE CARE KEEP POSTED.

---