hi everybody. ineed some help from you guys. i install an alarm(nitro bmw remote start)but having problem. dont know where to connect the door locks trigger, and the starter, yah it will start but you can notice that its still crankin it . so if any of you guys can help me out that would be great. and if its possible got som pics. thanx
I'm not too familiar with that alarm/remote start combo but, it sounds like you need to connect a tach wire.
Here are the wires that you are looking for:
Starter Wire: BLACK/ White in the Ignition harness
Lock: BLACK/ White in a gray connector above the fuse box usually wrapped with blue tape
Unlock: Orange in the same gray connector
Tach: Blue at the distributor
Good Luck
Starter | BLACK/ WHITE | IGNITION SWITCH HARNESS |
Power Lock | BLACK/ WHITE ( - ) | 3 PIN GRAY CONN. (COUPE/SEDAN) |
Power Unlock | ORANGE ( - ) | 4 PIN GRAY CONN. (WAGON) **** |
**** Door Lock Connector Taped To Harness In Dr. Kick Panel
**** Door Lock Connector Is Taped To Harness In Driver Kick Panel. Please Note This Connector Is NOT Available On SE Models. On SE Models Only, Door Lock Wires Can Be Accessed In 20 Pin Gray Connector In Passenger Kick Panel (Coupe) Or 8 Pin Gray Connector Behind Glove Box (Sedan) Or At OEM Keyless/ Security Module Under Passenger Front Seat.
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
hi everybody i did some connections but still got some problems. got some wires where to connect. pls correct me i do appreciated your help. heres what i did.do i need to put resistor / diode on relay?
12volts | white | + | ignition harness RED WIRE FROM BRAIN |
Starter | BLACK/ white | + | ignition harness GRAY FROM BRAIN |
Ignition | BLACK / YELLOW | + | ignition harness GREEN FROM BRAIN |
Power Lock | BLACK/ white | - | gray conn. above fuse ORANGE FROM CENTRAL LOCK GOES TO GROUND AND PURPLE TO THIS WIRE |
Notes: SE models, use factory alarm arm wire for lock and factory alarm disarm wire for unlock. |
Power Unlock | orange | - | box in blue tape BROWN GOES TO GROUND AND YELLOW TO THIS WIRE |
Notes: SE models, use factory alarm arm wire for lock and factory alarm disarm wire for unlock. |
Parking Lights+ | RED / black | | blue plug fuse box WHITE FRON BRAIN ONLY USE ONE WIRE BMW HAS SEPARETE PARKING LIGHTS THAS FOR YOU HAVE TWO WIRES |
Notes: Also a male blade terminal is available in the fusebox DKP. |
Factory Alarm Arm | RED / yellow | - | passenger kick or alarm |
Notes: Factory alarm is located under the passenger front seat. |
Factory Alarm Disarm | RED / blue | - | passenger kick or alarm YELLOW WIRE FROM BRAIN DON'T DO THE RELAY |
Notes: Factory alarm is located under the passenger front seat. |
Brake Wire | GREEN / WHITE | + | brake switch PURPLE WIRE BROM BRAIN |
i am not sure the green wire You HAVE TO UNDERSTAND THAT THE BRAIN IS FOR BMW AND BMW ONLY HAS 12V-IGNITION AND STARET ( NO ACC) AND YOU HAVE 2 ACCESORY WIRES.
GRAY WIRE CONECT TO A TOGGLE SWITCH ONE SIDE TO GROUND THE OTHER TO THE GRAY WIRE
NOTE: the yellow wire you have to use to power a relay to send 12v to accesory wire
87 12v
8612v
30 accesory wire (12ga)
85 yellow wire if car has factory alarm use diode to use the yellow wire
note:::: You can damage the computer of the car because the acc wire goes ground when the car crank . so is of to U
MY ADVISE IS GET A NEW BRAIN THAT HAS ACC OUTPUT
-------------
how own your mind, control your life.
MECP certified. always use a DMM
If you have an option to do a signal voltage do that.
-------------
Steve
Music Mart
Installer