1996 rover 600 OEM system.

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=58575
Printed Date: June 08, 2024 at 1:26 AM

Topic: 1996 rover 600 OEM system.

Posted By: Powermyster
Subject: 1996 rover 600 OEM system.
Date Posted: June 29, 2005 at 5:20 PM

my mate was messing with his car disconnected the alarm brain. (Valeo alarm) any way he connected it back and presto alarm LED stays on central locking isn't working and alarm is immobilised.

disconnected battery and nothing. still the same. usually when armed the led flashes he said its on solid though.

this car is honda accord derived. is accord oem alarm Valeo.

any suggestions i can't figure it out

Replies:

Posted By: dare_ds69
Date Posted: June 29, 2005 at 5:32 PM

try close all doors, locked whit the key wait like 5 minutes and unlocke twise with the key.

-------------
how own your mind, control your life.
MECP certified. always use a DMM

Posted By: Powermyster
Date Posted: June 29, 2005 at 5:41 PM

do you mean unlock lock unlock

or just do the unlock motion twice

Posted By: Powermyster
Date Posted: June 29, 2005 at 6:11 PM

didn't work both ways

any other idea's

Posted By: Powermyster
Date Posted: June 30, 2005 at 5:00 AM

abyone know if its the same as the accord alarm

Posted By: joe_1
Date Posted: June 30, 2005 at 3:27 PM

try holding in the lock button on the remote first for about 20 sec if that doesnt work try doing it with the ignition on if that dont work, suspect connections on alarm harness

Posted By: minihif44
Date Posted: July 01, 2005 at 12:47 PM

u could try this,this works on uk rover 600

remove the batteries and press one of the buttons for 10 seconds then reinstall batteries unlock car with key then press the lock button 4 times on the fourth press it should re sync and lock the doors

hope it helps

shaun

Posted By: Powermyster
Date Posted: July 02, 2005 at 4:54 AM

yeah he hasn't got any remote though apparently rover have a code. he is trying to get

just say the code is 3421

you like lock 3 times unlock 4 lock 2 unlock 1 with key in drivers door

something like that anyway will post if he gets the code

Posted By: joe_1
Date Posted: July 02, 2005 at 5:43 AM

yeah i know how to do that, the rover systems are so easy to bypass so if i was him i would just disable it

Posted By: Powermyster
Date Posted: July 02, 2005 at 6:39 AM

just ground the one wire to bypass al together isn't it

i gave him a diagram. dunno why he disconnected the alarm ecu in the first place

Posted By: joe_1
Date Posted: July 04, 2005 at 12:15 PM

yeah think it is BLACK/ red wire all the imob is on the rovers is to cut out the starter circuit so if you dont manage to bypass the control unit just do it at the starter relay so it is possible to crank the car

Posted By: Powermyster
Date Posted: July 05, 2005 at 4:46 AM

cool i thought it was on the fuel pump. ahh well thats what he said.

any ideas on his locking apparently the one brain controls alarm and central locking..

Posted By: joe_1
Date Posted: July 05, 2005 at 11:45 AM

well the rover systems i have done have just been the starter circuit and yes it is one control unit that does the door locks aswell if you cant get it to work just chop the central lock wires and make your own relays for it it is quite an easy system let me know how you get on

Posted By: Powermyster
Date Posted: July 06, 2005 at 5:35 AM

i'll let im know so

i think he is trying to get the code off rover

Posted By: Powermyster
Date Posted: July 12, 2005 at 6:25 AM

ok he tried to get the code from rover with no luck.

joe any tips for wiring relays to control the locking

Posted By: joe_1
Date Posted: July 13, 2005 at 11:38 AM

i know the motor wires are pink and orange and then you will have the switch wires going to the master solonoid in the drivers door cant remember the other colours think it was BLACK/ pink , BLACK/ red , black im sure it was neg control,

so all i would do is the 2 relay setup relay 1 = motor wire pin 30 , 12v + pin 87 and 86 and switch wire to pin 85 and neg - to pin 87a

relay 2 = motor wire pin 30 , 12v+ pin 87 and 86 , switch wire to pin 85 and neg to pin 87a

hope this helps get all the wiring at the control unit it is easyer to tap into