door lock/unlock wont work with 350hv

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=60635
Printed Date: May 04, 2024 at 11:27 PM

Topic: door lock/unlock wont work with 350hv

Posted By: littlepapa87
Subject: door lock/unlock wont work with 350hv
Date Posted: August 03, 2005 at 9:20 PM

I am installing a Viper 350HV system in my 92 Ford explorer. I have pre-existing power door locks, but not keyless entry. Everything was going well in the installation untill i got to the keyless entry. I can not tell how to wire the keyless entry from the provided instructions. the power lock switch has a pink/green wire that give off +12v when I press unlock and pink / YELLOW give off +12v when i press lock. There is one wire that gives off constant +12v and 2 grounds. I have tried tapping into the pink wires but it does not work. any help on how to install this would be greatly appreciated.

Replies:

Posted By: swamprat323
Date Posted: August 03, 2005 at 9:26 PM

your ahve 5 wire locks.

click here

Posted By: littlepapa87
Date Posted: August 03, 2005 at 9:31 PM

i saw that earlier but i dont understand how and where to put the alarm output wires

Posted By: swamprat323
Date Posted: August 03, 2005 at 9:39 PM

the green and blue wire form alarm will go to pins 85 and 86. look at those it say - from alarm lock out put an d- form alarms unlock out put.

Posted By: mo12v
Date Posted: August 03, 2005 at 9:46 PM

If your Explorer came WITHOUT Factory Keyless Entry:
U will need 2 SPDT Relays

Cut your PINK / YELLOW & PINK/Green wires in half

Relay 1

LOCK:
PIN 87 = PINK / YELLOW wire from Door Lock Actuator
PIN 87a = PINK / YELLOW wire from Door Lock Switch
PIN 30 = 12 Volts ( + ) Constant
PIN 85 = Negative Lock Output from Viper
PIN 86 = Constant 12 volt ( + )

Relay 2

UNLOCK:
PIN 87 = PINK/Green wire from Door Lock Actuator
PIN 87a = PINK/Green wire from Door Lock Switch
PIN 30 = 12 Volts ( + ) Constant
PIN 85 = Negative UNLock Output from Viper
PIN 86 = Constant 12 volt ( + )

If your Explorer came WITH Factory Keyless Entry:
Hook your Viper Lock / Unlock wires directly to the Factory wires ( don't cut them in half )

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: littlepapa87
Date Posted: August 03, 2005 at 9:53 PM

do you know where pins 85 and 86 are located on a 92 ford explorer

Posted By: mo12v
Date Posted: August 03, 2005 at 9:56 PM

WHOA.....................
The PINS that we are talking about will be on the 2 S P D T Relays that you need to install (Single Pole Double Throw)

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: mo12v
Date Posted: August 03, 2005 at 9:58 PM

If you are NOT familiar with this type installation, get help from someone who knows........ You CAN cause damage to your Door Lock Switches

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: littlepapa87
Date Posted: August 03, 2005 at 9:58 PM

ok i thought they were in the door panel that clears a lot up for me i believe i can get it from here thank you very much for all your help