Maxima 2001 & Compustar CM3000 Problem
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=62464
Printed Date: May 05, 2024 at 9:17 AM
Topic: Maxima 2001 & Compustar CM3000 Problem
Posted By: ekdude
Subject: Maxima 2001 & Compustar CM3000 Problem
Date Posted: September 09, 2005 at 11:49 PM
Car
Make: Nissan
Model: Maxima (Automatic)
Year: 2001
Alarm: Compustar 2W900FMR (CM3000)
Hello, I have 2 problems and any suggestions or help is greatly appreciated!
Problem # 1
I have installed the alarm and everything works except the lock/unlock (I) button on the pager remote. It doesn't unlock the doors at all...the funny thing is the 1 way remote will unlock all doors because it has separate buttons for the lock and unlock.. any clues? I'm thinking that it's a programming issue.... Problem # 2 (remote start)
I know that I need to have the bypass module installed before I can remote start the car. I haven't installed the bypass module yet, but when i press the black button on the brain to confirm if i have the right signal for tach it chirps 3 times... any body know where i can find this wire? Can someone send me a diagram of where I should be looking to find tach wire? Right now I've tapped this wire into a GREEN / WHITE wire in the ECM but it doens't seem to be the right one.
Question about the bypass module. It has red(+12), black(ground) and blue (wire that wraps around ingition coil). Now my question is for the red(+12v) wire, do i just give it constant +12v or which wire should I tap the red wire into for maximum security? I heard that if i give it +12v constant that means i'm always bypassing the immobilizor is this true? Thanks in advance!
Replies:
Posted By: ekdude
Date Posted: September 11, 2005 at 8:17 PM
what i am planning to do about the unlock is to go straight to the driver's door and hook it up that way....
Posted By: metaverse
Date Posted: September 11, 2005 at 8:21 PM
Here is a wiring diagram: Click me
If one remote works and the other does not, I would conclude a faulty remote.
Go to instrument cluster for tach.. Always works.
Good luck with Compustar, you already hit a snag with the remote.. Other experienced posters might contribute.
Posted By: ekdude
Date Posted: September 11, 2005 at 11:35 PM
should i give the bypass module red wire +12V constant or should i hook it up to the status output wire of the alarm which is on CN2 #2 BK ?
Posted By: Velocity Motors
Date Posted: September 11, 2005 at 11:50 PM
# 1: Does the 2 way pager remote start the car or let you know that the hood is open or doors open when armed ? If not, then it's not programmed yet. #2 : As suggested you can go to the instrument cluster or you can go to the injector and grab the uncommon colored wire. This always works for me. # 3 : I'm not sure why you don't have a status inpt wire or ground when running wire on this module. Usually you have the (+) go to constant and when the remote starter engages, the status wire turns on the system. The blue (wire that wraps around ingition coil) what polarity is it asking for ? ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: ekdude
Date Posted: September 12, 2005 at 2:46 AM
#1 the 2way remote doesn't remote start yet cuz i don't have the bypass module installed and don't have the right tach wire. But it will tell you that the hood or the doors are open. I know this car needs a 2nd pulse to open all doors. #2 I will do just that. #3 This alarm does have a status input wire (ground out when running). Just to confirm do i hook +12V constant to the status input wire? As for the blue wire i haven't a clue what polarity it is...i must find out. Velocity Motors wrote:
# 1: Does the 2 way pager remote start the car or let you know that the hood is open or doors open when armed ? If not, then it's not programmed yet. #2 : As suggested you can go to the instrument cluster or you can go to the injector and grab the uncommon colored wire. This always works for me. # 3 : I'm not sure why you don't have a status inpt wire or ground when running wire on this module. Usually you have the (+) go to constant and when the remote starter engages, the status wire turns on the system. The blue (wire that wraps around ingition coil) what polarity is it asking for ?
Posted By: thepencil
Date Posted: September 12, 2005 at 9:46 AM
ekdude wrote:
should i give the bypass module red wire +12V constant or should i hook it up to the status output wire of the alarm which is on CN2 #2 BK ?
+12V constant to the bypass module and the Black Status Output to the ground wire of the Bypass moduel is the right connection.
It bypass will not be on all the time as you were wondering. The black status output also refers to (ground out when running) wire will only activate (becomes Ground) during the remote start period. Otherwise it's off the rest of the time. ------------- Be careful whose advice you buy, but be patient with those who supply it. 
Posted By: ekdude
Date Posted: September 12, 2005 at 9:32 PM
Hey guys! I got all the problems solved and the alarm is in working order, Thanks too all that gave me the support! I only wonder how do i stop the factory alarm from setting off? cuz when i use the 2way remote to unlock all doors, sometimes the factory alarm sets off... any clues?
Posted By: Velocity Motors
Date Posted: September 12, 2005 at 9:48 PM
The OEM disarm wire has to be hooked up to the Compustar alarm disarm wire. FACTORY ALARM DISARM--------ORANGE / blue-------|- |located at pin 30 at SECU.The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: ekdude
Date Posted: September 13, 2005 at 12:58 AM
Thanks! i got it going... awesome!
Posted By: Velocity Motors
Date Posted: September 13, 2005 at 10:53 AM
No problemo
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
|