04 Buick Regal remote start wiring

I need a wiring diagram for a 2004 Buick Regal please. I am going to be installing a remote starter.

12volts  red (x2)  +  ignition harness Starter  yellow  +  ignition harness Second Starter  N/A     Ignition  pink  +  ignition harness Second Ignition  white to dk. green  +  ignition harness Third Ignition  N/A     Accessory  orange  +  ignition harness Second Accessory  brown  +  ignition harness Keysense  lt. green  -  ign harn or BCM, purple plug, pin A1 Notes: The BCM (Body Control Module) is to the left of the steering column. Power Lock  RED / black  -  BCM, purple plug, pin B6 Notes: The BCM (Body Control Module) is to the left of the steering column. Power Unlock  ORANGE / black  -  BCM, purple plug, pin A6 Notes: The BCM (Body Control Module) is to the left of the steering column. Lock Motor  gray  5wi  BCM, clear plug, pin G Notes: The BCM (Body Control Module) is to the left of the steering column. Unlock Motor  tan  5wi  BCM, clear plug, pin E Notes: The BCM (Body Control Module) is to the left of the steering column. Parking Lights+  lt. blue (larger of 2)  +  headlight switch Parking Lights-  gray/black  -  BCM, lt. blue plug, pin A4 Notes: The BCM (Body Control Module) is to the left of the steering column. Hazards  same as turn signals     Turn Signal(L)  lt. blue (F), yellow (R)  +  steering column Turn Signal(R)  dk. blue (F), dk. green (R)  +  steering column Reverse Light  dk. blue  -  BCM, lt. blue plug, pin A8 Notes: The BCM (Body Control Module) is to the left of the steering column. Door Trigger  dk. blue/white  -  BCM, purple plug, pin A5 Notes: The BCM (Body Control Module) is to the left of the steering column. Dome Supervision  use door trigger wire     Trunk/Hatch Pin  ORANGE / black  -  BCM, lt. blue plug, pin B4 Notes: The BCM (Body Control Module) is to the left of the steering column. Hood Pin  N/A     Trunk/Hatch Release  white  -  BCM, purple plug, pin A7 Notes: The BCM (Body Control Module) is to the left of the steering column. Power Sliding Door  N/A     Factory Alarm Arm  N/A     Factory Alarm Disarm  N/A     Disarm No Unlock  N/A     Tachometer  PURPLE / white or white  ac  ignition control module Notes: The ignition control module is on the top right front of the engine. Wait to start  N/A     Brake Wire  white  +  brake pedal switch or column Parking Brake  lt. blue  -  BCM, purple plug, pin A2 Notes: The BCM (Body Control Module) is to the left of the steering column. Horn Trigger  black  -  column or BCM, lt. blue plug, pin A5 Notes: The BCM (Body Control Module) is to the left of the steering column. Memory Seat 1  N/A     Memory Seat 2  N/A     Memory Seat 3  N/A     Interface Module: Category: Immobilizer Bypass Required: Yes Type: VATS Part #: 652T resistor pack Alternate Part1 #: DesignTech 20402 Alternate Part2 #: DesignTech 29402 Notes: See DirectFax document 1049 for interface information.

-------------
D

MECP First Class Certified Installer.

Nothing is impossable, it's just more expensive.

Thank you. Is this an easy install? Any tips or tricks to help me through it?

Also, I bought the DEI Immobilizer Byass that was suggested. Any help in installing this?

the install does not look to bad to me but i do them all the time.

-------------
D

MECP First Class Certified Installer.

Nothing is impossable, it's just more expensive.

Ok I got the 562T bypass system. It has 5 wires, red, black, orange, yellow, and brown. I know the red and black are hot and ground, but what are the yellow, orange, and brown wires for exactly?

And which one do I wire the resistor in?

I mean the 652t, not 562t