Installing Alarm in Acura Cl 99

I'm trying to hook up a Ungo two way alarm, but need the diagram for a

Acura Cl 99 2.3. Does any one have? Thanks!

|       ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |
|              12V|white               |+  |ignition harness            |
|          STARTER|BLACK/ white         |+  |ignition harness            |
|         IGNITION|BLACK / YELLOW *1     |+  |ignition harness            |
|        ACCESSORY|yellow              |+  |ignition harness            |
|       POWER LOCK|RED / yellow          |-  |security module *3          |
|     POWER UNLOCK|RED / blue            |-  |security module *3          |
|       LOCK MOTOR|WHITE/ red           |   |security module *3          |
|     UNLOCK MOTOR|gray                |   |security module *3          |
|    DISARM DEFEAT|yellow/red          |   |security module *3          |
| PARKING LIGHTS +|RED / black           |   |security module *3          |
|       HEADLIGHTS|blue/black or blue  |-  |headlight switch            |
|     DOOR TRIGGER|BLACK/ white         |-  |security module *3          |
| DOME SUPERVISION|use door trigger    |   |                            |
|  TRUNK/HATCH PIN|lt. GREEN/ black     |-  |security module *3          |
|         HOOD PIN|lt. green           |-  |security module *3          |
|TRNK/HTCH RELEASE|blue/red *4         |5wi|security module *3          |
|  FCTRY ALARM ARM|arms with lock      |   |                            |
|FCTRY ALRM DISARM|disarms with unlock |   |                            |
| DISARM NO UNLOCK|blue                |-  |security module *3          |
|       TACHOMETER|blue                |   |tach test conn. *2          |
|      SPEED SENSE|orange              |   |PCM *5                      |
|       BRAKE WIRE|GREEN / WHITE         |+  |brake switch                |
|     HORN TRIGGER|blue/red            |-  |steering column             |
|           WIPERS|blue / YELLOW         |-  |steering column             |
|  LF WINDOW UP/DN|RED / yel  -  RED / blue|A  |drivers door motor          |
|  RF WINDOW UP/DN|blue/yel  -  blue   |A  |drivers door harness        |
|        RADIO 12V|WHITE/ yellow        |+  |radio                       |
|     RADIO GROUND|black               |-  |radio                       |
|     RADIO SWITCH|WHITE/ red           |+  |radio                       |
| RADIO ILLUMINATE|RED / black           |+  |radio                       |
|    POWER ANTENNA|yellow/white        |+  |radio                       |
|       LF SPEAKER|blu/grn - gry/blk   |   |radio or amplifier *6       |
|       RF SPEAKER|RED / grn - brn/blk   |   |radio or amplifier *6       |
|       LR SPEAKER|blu/yel - gry/wht   |   |radio or amplifier *6       |
|       RR SPEAKER|RED / yel - brn/wht   |   |radio or amplifier *6       |

Notes:
NOTE: This vehicle has an immobilizer system that needs to be bypassed when adding remote start. Use DEI part number 555U.  *1 Also found yellow/gray at the security module. Do not use the yellow/gray for remote start.  *2 The tach test connector is a 2 pin connector located on the passenger side of the engine compartment by the firewall taped to a harness.  *3 The security module is located under the passenger seat.   *4 This wire must be relay isolated from the security module.  *5 PCM is under the passenger dash, under the floor board.  *6 If equipped, the stereo amplifier is on the right rear corner of the trunk.

Do the wires need to be ran under the passenger seat?

Thanks in advance!