2005 Honda CRV remote start wiring?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=67186
Printed Date: May 17, 2025 at 8:02 AM
Topic: 2005 Honda CRV remote start wiring?
Posted By: crv2005
Subject: 2005 Honda CRV remote start wiring?
Date Posted: November 28, 2005 at 11:08 AM
Hi, I am looking to install a remote starter on a Honda CRV(EX) 2005 and I wanted to know if anyone had the wiring diagram. before I get started, I wanted to know exactly what to look for, also would like to install a passkey since i have a factory alarm. Suggestions are appriciated. Thanks:)
Replies:
Posted By: the12volt
Date Posted: November 28, 2005 at 11:17 AM
Posted By: crv2005
Date Posted: December 12, 2005 at 7:16 PM
Thanks, Besides the remote starter, what other components would i need since i have a factory alarm and one of those keys with a chip insde. I would want to dis/arm my factory alarm and be able to open/close the door locks and romte start the vehicle with the same remote.
Posted By: wiretapper
Date Posted: December 12, 2005 at 7:51 PM
Fact. alarm system is a stand alone piece. There's no way around it to use a disarm wire. You either dump the fact. alarm and install aftermarket alarm/starter combo, or carry two remotes and disarm the system before remote starting. Also the fact. remotes won't work while the vehicle is running. I just did an '05 last week that had no fact. alarm. I got lucky.
Posted By: crv2005
Date Posted: December 12, 2005 at 9:30 PM
What are the HODL3 and the PKH3 for? I am not sure which one to use with the factory alarm when using a remote starter. I have read on some posts that you need both, but I am not sure for the CRV.
Posted By: wiretapper
Date Posted: December 12, 2005 at 9:39 PM
Not sure about either of those, but the DEI 555HW woks just fine for the transponder bypass.
Posted By: navigator2004
Date Posted: December 17, 2005 at 11:35 PM
How do you install a Remote Start Add-on to a Factory Keyless Entry System? I have a 04 Navigator and a Startnr2 Remote Start with the PKF3 Bypass. If I ground the Trigger, it starts the vehicle; however, I can't find a Negative Pulse from the Keyless Entry that will allow me to Remote Start the Vehicle. Thanks, Kenny ------------- Navigator2004
Posted By: gus1
Date Posted: December 18, 2005 at 12:59 AM
Yo... wiretapper...
Factory disarm is in the door.... test with key in door. At the Driver's door module. The whole "carry 2 remotes" BS is only for installers too lazy to go get the proper arm and disarm wires.
555HW doesen;t work as nicely as the 556H. The HODL is a doorlock interface..... doorlocks are negative in the kick (think Civic), and the DL piece will also do disarm I believe. The PKH3 should do the transponder bypass.
Gus
-------------
Wherever I go, that is where I end up......
Posted By: crv2005
Date Posted: December 18, 2005 at 7:37 AM
How about the wipers, how can I cut the power when the remote starter is activated. I do not want to burn the motor. 
Posted By: gus1
Date Posted: December 18, 2005 at 8:33 AM
Find the wiper motor, use a relay.
You need to power up both acessories (WHITE/ red, and I believe yellow). Not sure which one the wipers live on, and what else lives on that Acessory circuit... but if it is that much of a concern, find the wiper motor, and interrupt the power to it using a relay running off of a negative second ignition output.
Gus
-------------
Wherever I go, that is where I end up......
|
the12volt •