98 4runner Remote Start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=67696
Printed Date: June 29, 2025 at 12:50 AM
Topic: 98 4runner Remote Start
Posted By: quebert00
Subject: 98 4runner Remote Start
Date Posted: December 05, 2005 at 11:29 AM
I am going to be installing a remote start on a 98 4runner. Does anyone know how to bypass the factory alarm? The wiring diagrams I have don't have anything listed for Factory Arm or Disarm. I believe this unit is a RS-3000. Let me know.
Thanks in advance!
Replies:
Posted By: quebert00
Date Posted: December 05, 2005 at 11:32 AM
Or does this unit only need a lock/unlock pulse to disarm and rearm the alarm?
Posted By: northern
Date Posted: December 05, 2005 at 12:28 PM
Just did a 97 4runner. But that model did not have a factory alarm.
Posted By: quebert00
Date Posted: December 05, 2005 at 8:17 PM
Anyone else have an idea?
Posted By: mobileworks
Date Posted: December 05, 2005 at 10:27 PM
Remote Starter Wiring Colors and Notes |
Function | | Vehicle Color | Location | Start: | | BLACK | IGNITION SWITCH HARNESS | Ignition #1: | | BLACK/ RED | IGNITION SWITCH HARNESS | Ignition #2: | | BLACK / YELLOW | IGNITION SWITCH HARNESS | Ignition #3: | | N/A | | Accessory: | | BLUE/RED | IGNITION SWITCH HARNESS | Brake Light: | | GREEN / WHITE (+) | AT SWITCH ABOVE BRAKE PEDAL | Tach Signal: | | BLACK | AT IGNITER ON PASS. WHEELWELL * | Parking Lights: | | GREEN (+) | 13 PIN CONNECTOR AT FUSE BLOCK ** | Headlights: | | RED (-) | AT HEADLIGHT SWITCH ** | Diesel Glow Plug: | | | | Clutch Bypass Wire: | | |
| NOTES: * BLACK Tach Wire Also Found In Data Link Connector On Driver Side Of Engine (4 Cyld.) Or At Engine Control Module Located Behind Pass. Dash (6 Cyld.) Or Can Also Be Found In 26 Pin Connector In Pass. Kick Panel On Both. |
Alarm and Keyless Entry Wiring Colors |
Function | | Vehicle Color | Location | Constant +12 Volts: | | WHITE/ RED & WHITE | IGNITION SWITCH HARNESS | OEM Alarm Disarm: | | N/A | IN SCHEMATICS | Dome Lights/Superv: | | BLACK/ WHITE (-) | 26 PIN CONNECTOR IN DRIVER KICK PANEL | OEM Horn: | | GREEN/ RED (-) | STEERING COLUMN HARNESS | Power Lock: | | RED / WHITE | 13 PIN BLUE CONN. IN DRIVER'S KICK *** | Power Unlock: | | RED / YELLOW | 13 PIN BLUE CONN. IN DRIVER'S KICK *** | Trunk Release: | | BLACK / YELLOW | 26 PIN CONN. IN DR. KICK PANEL | Alarm Input Wire: | | BLACK/ WHITE (-) | 26 PIN CONNECTOR IN DRIVER KICK PANEL | NOTES: ** Fuse Block Located In Driver Dash. *** Child Safety Locks: RED / BLUE (-) In Same Conn. As Door Lock Wires Above. |
-------------
Posted By: secureauto
Date Posted: December 05, 2005 at 10:32 PM
Is it a keyless upgrade? does it have a light pod under the dash? It could also be a factory Toyota upgrade alarm installed at the dealer, those are usually T-harnessed.
-------------
ASE Certified
Posted By: quebert00
Date Posted: December 06, 2005 at 11:11 AM
I believe it is a factory Toyota alarm installed at the dealer. The unit is under the drivers seat and it does have the secuirty light on the console. It does look as though all of the wires where connected with T-Taps.
What does this mean??OEM Alarm Disarm: N/A IN SCHEMATICS
Posted By: Mike M2
Date Posted: December 06, 2005 at 3:10 PM
Any Toyota alarm starting with RS is dealer installed. I know they do connect to the keysense, but i'm not sure if it will disarm the alarm. Honestly, you may not have to. Most only have a starterkill and no shock sensor, just like an aftermarket. If that's the case just apply your starter wire after the the T harness at the ignition switch and let it stay on....
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: Scott35
Date Posted: December 06, 2005 at 5:06 PM
On that kind of alarm you could just remove it.
-------------
Tacomacrew
Posted By: quebert00
Date Posted: December 06, 2005 at 7:03 PM
It does have a shock sensor I saw it under the dash. The alarm will sound if you hit the glass to hard or open a door while armed.
Posted By: infinkc
Date Posted: December 06, 2005 at 7:11 PM
you can just remove it, but have to take off the harness that goes in between the ignition swith and the harness, or you car wont start, you can also use the factory led still of you want with an aftermarket alarm.
-------------
There are 10 types of people in the world, ones that understand binary and ones that dont.
Posted By: quebert00
Date Posted: December 07, 2005 at 1:18 PM
I could remove it but I would rather leave it in and be able to control it.
|