negative trigger locks with a dei 451m
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=67706
Printed Date: May 28, 2024 at 9:26 PM
Topic: negative trigger locks with a dei 451m
Posted By: r2d97
Subject: negative trigger locks with a dei 451m
Date Posted: December 05, 2005 at 2:03 PM
I am going to install a rattler 369d remote start keyless entry system in an 1994 honda acccord ex sedan. I was wondering on how to hook up the 451 m to this locking system I am slightly confused and was hoping someone could clarify this for me. I know that this is a - trigger locking system as with most if not all honda's. The install instructions with the 369d are telling me to cut the connector off of the 451m that plugs into the brain? Is this so? I have heard that I could just plug this into the brain and purple to +12 and green to lock and blue to unlock. Am I right or is there another method of doing this. The manual kinda confused me. The brain should be able to provide ample amount of power to trip the relay Right? Thank you for any info that could help me.
Replies:
Posted By: infinkc
Date Posted: December 05, 2005 at 2:24 PM
is there a reason you need to use the 451m for the locks?
-------------
There are 10 types of people in the world, ones that understand binary and ones that dont.
Posted By: r2d97
Date Posted: December 05, 2005 at 3:13 PM
I am pretty sure that i am supposed to use this module that came with the rattler. How do ai wire this up if I do.
Posted By: kgerry
Date Posted: December 05, 2005 at 3:24 PM
you dont need it.... i only use them when doing reverse polarity locks....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: r2d97
Date Posted: December 05, 2005 at 3:33 PM
I don't inderstand? how am I gonna get key less entry then if I don't use this?
Posted By: kgerry
Date Posted: December 05, 2005 at 3:40 PM
did the rattler not come with the standard, Green /Blue 2 wire door lock plug? if not then you'll need to use the 451, although you really dont need this module, the default out on DEI units is negative trigger.... you could cut the plug off but why not just use the module? ground the violet wire with the fuse and then the GREEN/ black & blue/black will be negative outputs..... ------------- Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: r2d97
Date Posted: December 05, 2005 at 3:52 PM
all that i got was the 451 m and that has a green, red, blue three pin harness along with 5 other wires that are colored purple, blue, green, brown, and white. sorry to make this so confusing .
Posted By: auex
Date Posted: December 05, 2005 at 6:55 PM
Plug module in, ground purple wire, then use the blue and green for outputs. Or you can cut the relay off, cap off the red and use the blue and green wires there for outputs. Do either.
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: Slammed_Am
Date Posted: December 06, 2005 at 12:38 AM
you could also just use the thin wires from the 451M harness that plugs into the brain. (green as lock, blue as unlock) and not use the 451M.
Posted By: r2d97
Date Posted: December 06, 2005 at 7:17 PM
Thank you soo much. So I guess that the only reason to use the relay is to have maximum power to operate the door locking system? I appreciate all of everyones help.
|