Compustar 2WSS-AS start problem
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=68788
Printed Date: May 20, 2025 at 7:58 AM
Topic: Compustar 2WSS-AS start problem
Posted By: viptime
Subject: Compustar 2WSS-AS start problem
Date Posted: December 20, 2005 at 7:23 AM
Compustar 2WSS-AS start problem
Finished installing Compustar 2WSS-AS today and it the starter don’t work. I followed https://forums.clubrsx.com/showthread...ruha+compustar instructions. I cut the jumper wire in side of the main unit to make it work with automatic transmission
Tachometer was learned successfully as indicated by one beep (so some things work;)) but it still will not start. (no cranking or any signs of life) After I push the (II) button for 2 sec to start. Remote beeps 3 times -> car beeps 3 times -> car flashes 2 times and after a few sec. pause it flashes 7 times (indicating Reservation mode OFF) it suppose to be a manual transmission code only and I got 02 RSX Automatic.
. Any help is appreciated.
Replies:
Posted By: viptime
Date Posted: December 20, 2005 at 7:45 AM
Posted By: Velocity Motors
Date Posted: December 20, 2005 at 8:13 AM
When you cut the GREEN / WHITE wire inside the CPU did you separate the wires ? Also, make sure you test for residual power on the ignition switch incase the 2 flashes after the 3 beeps was also a indication of your problem.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: viptime
Date Posted: December 20, 2005 at 10:17 AM
Thank you Velocity Motors,
I just rechecked all the connections and it checked out 100%. The GREEN / WHITE jumper wire is cut and separated.
Could you please tell me how to check the residual power on ignition switch.
Thank you
Posted By: 05gt
Date Posted: December 20, 2005 at 3:31 PM
are you using this unit just for remote start purposes disconnect the parking brake wire and the doorpin wires from the brain if you are using this unit for alarm/remote start purposes just disconnect the park brake wire from the brain this should solve the problem
Posted By: viptime
Date Posted: December 20, 2005 at 5:52 PM
tdisconnected the park brake wire and still no start
Posted By: viptime
Date Posted: December 21, 2005 at 7:45 AM
Anyone, any suggestions?
Posted By: viptime
Date Posted: December 21, 2005 at 10:37 AM
I set the reservation mode and it started up. How go I get this thing to understand that it is automatic. The wires are cut and separated, I don’t know what else to do. Turning key on and off did not work. I also tried taking out power fused and the battery out of the remote to reset the system. There has to be some way to do it.
Thank you for everyone.
Posted By: tcool
Date Posted: December 22, 2005 at 2:13 AM
The new compustars don't use the jumper inside the unit for automatic transmissions anymore. However, the ones I have don't have the green white wire anymore, and have a big sticker on the dipswitch door that states "Manual" or "Automatic". I would call Ray in tech support at Firstech 888-820-3690 and describe the problem. Maybe they sent out some of the newer dedicated units with the jumper wire. If not, you probably have a defective brain. ------------- bzzzzttttt
|