2003 envoy, remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=69375
Printed Date: May 25, 2024 at 7:14 AM
Topic: 2003 envoy, remote start
Posted By: ryguy
Subject: 2003 envoy, remote start
Date Posted: December 28, 2005 at 10:00 AM
any one have any info on useing a dei 457g on remote starter on this vehicle . remote starts fine but security light stays on when u start with the key ?? any info would be good.thanks!
Replies:
Posted By: kgerry
Date Posted: December 28, 2005 at 12:14 PM
i have a 457G installed on my own 03 Envoy without this issue... no problems at all in fact.....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: wiretapper
Date Posted: December 28, 2005 at 4:41 PM
Check the remote start "ground when running" wire and make sure it's not grounded when you use the key. Either that, or use a relay and the key sense wire to open up the ground trigger to the 457G when you put the key in.
Posted By: ryguy
Date Posted: December 28, 2005 at 6:52 PM
thanks ! I will c what i can do ,thinking it may be a ground problem ill go from there
Posted By: chris354
Date Posted: December 28, 2005 at 8:31 PM
Make sure you power the brown acc wire also.
Posted By: extreme1
Date Posted: December 28, 2005 at 10:50 PM
chris354 wrote:
Make sure you power the brown acc wire also.
why?? ------------- Shaughn Murley
Install Manager, Dealer Services
Visions Electronics
Red Deer, Alberta
Posted By: chris354
Date Posted: December 28, 2005 at 11:59 PM
Moderator X wrote:
Chris,
In most of the new GM vehicles that we list the brown wire as needing to be powered any or all of the following can/will occur if the brown second acc wire is not triggered.
No crank
SRS light on
No PL read
4wd issues
If you've had success to this date with not powering the brown wire, keep your fingers crossed or whatever you guys are doing to fool the BCM to believing it's seeing a signal it needs
Posted By: ryguy
Date Posted: December 29, 2005 at 9:47 AM
thanks guys for all your help i will find out in about a hour when it comes in and i get under there 2 c
-------------
MECP installer,technician
Posted By: uffdog
Date Posted: December 29, 2005 at 7:29 PM
Disconnect the battery for 5 minutes and it should take the light out, this happened on my 03 Trailblazer and I disconnected the battery neg and it cured the problem up.
-------------
RFD
Posted By: ryguy
Date Posted: December 29, 2005 at 8:36 PM
did it come on only when the key was in use ? remote starts fine no security light use the key only the light come on i guess the truck locked up told them to leave the key on for 5 mins. havent got to c the truck yet but maybe tomarrow
-------------
MECP installer,technician
Posted By: ryguy
Date Posted: December 30, 2005 at 3:07 PM
well i checked the grounds all my connections re soddered some to double check , then said heck with it and put a resistor on the passlock wire with a relay and madea loop . i figure the module was bad so im only useing the door lock feature of it . thanks for the replys guys   ------------- MECP installer,technician
|