remote start/Honda CRV

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=72066
Printed Date: May 13, 2025 at 11:38 AM

Topic: remote start/Honda CRV

Posted By: kyle2000
Subject: remote start/Honda CRV
Date Posted: February 02, 2006 at 6:41 PM

I just installed a crimestopper model# RS-999-TW1 on a 2004 Honda CRV. The problem is that the remote start works but using the factory key no longer will start the engine; it just cranks over. would appreciate any suggestions. This is my first(and last) install.

Replies:

Posted By: mo12v
Date Posted: February 02, 2006 at 6:57 PM

Did you cut any of the Ignition wires or install a Relay for Ignition Kill?

Also what type ByPASS did you use??

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: kyle2000
Date Posted: February 02, 2006 at 7:20 PM

Yes. I forgot to mention that i also installed an Omega IB_H3 Immobilizer by-pass module along with it. I followed the instructions for this module to a 'T'. One of the wires from the module(data output) was spliced into one of the wires (position #2)on the 7-pin ignition switch assembly and another wire from position \#6 was cut and spliced to run through the by-pass module. I only cam upon this problem right after I made this splice.

Posted By: mo12v
Date Posted: February 02, 2006 at 8:27 PM

Check your ByPASS :

RED is to Constant 12Volt +
BLACK is to GROUND
PINK / White is to IGNITION Switch Side of cut wire}
BLUE is to ECM ( Car ) side of cut wire

Also recheck your Ignition wires

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: kyle2000
Date Posted: February 02, 2006 at 9:20 PM

the instructions that came with the by=pass module gave the following.

brown=to remote start unit, black- ground, blue- ignition out, red- ignition from ECM, violet- data input. are you saying this is incorrect?

Posted By: mo12v
Date Posted: February 02, 2006 at 10:17 PM

You are correct if you are using the 6 wire ByPASS
Check your ByPASS :

RED is to ECM (Car ) side+
BLUE is to IGNITION Switch Side of cut wire
VIOLET is to DATA PIN 2
BLACK is to Ground

Also recheck your Ignition wires

Sorry, I thought you may be using the 10 wire Upgrade Version posted_image

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Posted By: wiretapper
Date Posted: February 04, 2006 at 2:52 AM

kyle2000 wrote:

Yes. I forgot to mention that i also installed an Omega IB_H3 Immobilizer by-pass module along with it. I followed the instructions for this module to a 'T'. One of the wires from the module(data output) was spliced into one of the wires (position #2)on the 7-pin ignition switch assembly and another wire from position \#6 was cut and spliced to run through the by-pass module. I only cam upon this problem right after I made this splice.

Recheck the wiring on the bypass module, or just try reversing the cut wire. DEI had the wrong info on the CRV. Maybe your info is wrong too. I went through the same thing you did on an '06 and switched the wires. Worked perfect immediately after. You can't go by the wire color, you have to go by wire function.

Posted By: kyle2000
Date Posted: February 04, 2006 at 5:42 PM

thanks for the information, I will certainly give that a try.