power window roll up module prob

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=73109
Printed Date: May 14, 2024 at 4:35 PM

Topic: power window roll up module prob

Posted By: mustangfoo
Subject: power window roll up module prob
Date Posted: February 18, 2006 at 10:31 PM

ok guys I have had pretty much everything down on my installations, but this one is stumping me!!!! I bought two of these to control both my front and back windows up and down. but I am lost and which wires control what and what they do even though I have the instructions lol. If anybody can explain these crazy instructions, I would greatly appreciate it!!! THANKS!!!

posted_image

Replies:

Posted By: cntrylvr79
Date Posted: February 18, 2006 at 10:35 PM

would help if we knew the year, make, and model of the vehicle.

-------------
Cause I'm So white and nerdy...
First Class Certi-fried installer

Posted By: mustangfoo
Date Posted: February 18, 2006 at 10:53 PM

94 Suzuki Sidekick, but did not come factory with power windows. I installed a universal kit which has a solid wire and solid wire with a stripe and white wire which I think is the illumination for the switch but not sure and has a yellow and pink wire leading to the motor.

Posted By: cntrylvr79
Date Posted: February 18, 2006 at 11:46 PM

Here goes you're going to have to find each pair of wires for the windows. The wires should rest at ground and when you push the up/down button one of the wires will go to +12v. You can probably get all four pairs at the master switch. Once you locate all the wires, you'll have to cut each pair in half. I would recommend doing that 1 window at a time so you don't get all confused. Then wire up the controllers as follows.

BLACK/ white loop - cut it and isolate each end of the wires
White - Switch side of left front window up wire
WHITE/ blue - other side of window up wire
Blue - Switch side of left front window down wire
Blue/black - other side of left front window down wire
Red - Constant +12v
Black - Ground
Brown - Switch side of Right Front window up wire
BROWN / blue - other side of right front window up wire
Green - switch side or right front window down wire
GREEN/ black - otehr side of right front window down wire
Yellow/white - Aux output from alarm that will put the windows down
Yellow - aux out from alarm that will put the windows up

Wire up the second controller the same as the first just use the rear windows. Good luck hope this helps you

-------------
Cause I'm So white and nerdy...
First Class Certi-fried installer

Posted By: mustangfoo
Date Posted: February 19, 2006 at 7:26 PM

thats great thanks a lot, just one quick question when you say switch side what exactly do you mean??? I have a yellow and pink wire two black wires(driver side) the others are solid color and solid with red stripe and a white wire from the harness of the switch

Posted By: mustangfoo
Date Posted: February 20, 2006 at 12:16 AM

haha ok nm my idiotic self figured out what you meant took me long enough thinking about it!!! sorry about my slow self!!! thanks a lot for the help!!!

Posted By: KPierson
Date Posted: February 20, 2006 at 11:12 AM

Does that window module raise both windows at the same time? Where did you pick it up from?

-------------
Kevin Pierson

Posted By: AZ-ss
Date Posted: February 20, 2006 at 5:11 PM

KPierson wrote:

Does that window module raise both windows at the same time? Where did you pick it up from?

Nope! Looks like asianwolf product instructions. It does one window at a time, unless you have the TWO window module. That one does both windows simultaneously.