97 Dodge Intrepid Remote Keyless
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=77445
Printed Date: July 05, 2025 at 11:24 PM
Topic: 97 Dodge Intrepid Remote Keyless
Posted By: zues79
Subject: 97 Dodge Intrepid Remote Keyless
Date Posted: May 08, 2006 at 11:11 AM
I have the Exact same brand and model as the one in this Post---> Click Here
So the manual and diagrams are the same. Can anyone give me a basic step by step on how to do this for a 97 dodge Intrepid.
Here are a few Wiring Diagrams I Found
#1
#2
Any Help at all will be greatly appreciated.
Replies:
Posted By: mo12v
Date Posted: May 08, 2006 at 12:22 PM
Door Locks: ORANGE = N/C
WHITE = LOCK wire
YELLOW = 12 Volts CONSTANT
ORANGE / Black = N/C
WHITE / Black = UNLOCK wire
YELLOW / Black = 12 Volts CONSTANT ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: zues79
Date Posted: May 08, 2006 at 1:37 PM
sorry but what does n/c mean?
Posted By: zues79
Date Posted: May 08, 2006 at 1:59 PM
no change?
Posted By: xtremej
Date Posted: May 08, 2006 at 3:43 PM
No connection.
-------------
Posted By: mo12v
Date Posted: May 08, 2006 at 4:40 PM
yep..........No connection.
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: zues79
Date Posted: May 08, 2006 at 5:42 PM
ok thnx for the help do i need to use the engine cut off???
Posted By: mo12v
Date Posted: May 08, 2006 at 6:03 PM
Only if you want the added Security.
That involves cutting your Starter wire in Half and attaching the wires as shown in Instructions
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: zues79
Date Posted: May 08, 2006 at 9:18 PM
i think ill pass on cutting the wire from the starter....well i think im gonna try this tommorrow..
is there anything else that i should know before starting this?
Posted By: mo12v
Date Posted: May 08, 2006 at 9:21 PM
Test, Retest & Make sure of your Connections. Best to Solder & Tape.
-------------
MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: cntrylvr79
Date Posted: May 09, 2006 at 9:48 AM
Don't forget you have to remove the entire lower dash to get to the wiring. Which can suck if you're not paying attention.
-------------
Cause I'm So white and nerdy...
First Class Certi-fried installer
Posted By: zues79
Date Posted: May 09, 2006 at 10:39 AM
are you talkin about ALL the wires?
I heard you can just get to the wires behind the kicker panel on the drivers side PLEASE tell me if im wrong i dont want to mess anything up.
and is there anything you have to connect to the fuse box or can wire to the fusebox?
Posted By: xtremej
Date Posted: May 09, 2006 at 10:46 AM
You get the lock and unlock wires are in the kick, the ignition harness which has you power wires and such is behind the drivers dash. To make it easier on yourself you can remove the lower column cover and access the ignition harness also.
-------------
Posted By: zues79
Date Posted: May 09, 2006 at 11:13 AM
ok ill check it out tonite and see what i have to work with.
I dont have to go al the way to the ignition do I ?
Posted By: xtremej
Date Posted: May 09, 2006 at 11:53 AM
If you are not doing a starter kill, no you just need a constant 12v. You might be able to grab that in the kick can't remember. -------------
Posted By: zues79
Date Posted: May 09, 2006 at 1:19 PM
ok since im not doin the starter kill i dont need to take apart the bottom of the dash?
Posted By: xtremej
Date Posted: May 09, 2006 at 1:49 PM
Not if you can find a constant 12v in the kick..
-------------
Posted By: zues79
Date Posted: May 09, 2006 at 1:53 PM
ok thanks again well im gonna try this in a lil while hope it all works out good thnx for the help.
Zues
Posted By: xtremej
Date Posted: May 09, 2006 at 1:54 PM
not a problem..
-------------
Posted By: zues79
Date Posted: May 10, 2006 at 11:24 AM
Does the acc wire have to be hooked up if im not using the starter kill?
Posted By: zues79
Date Posted: May 10, 2006 at 11:25 AM
and where else can i connect the unlock wire does it have to be the one behind the fuse box?
Posted By: zues79
Date Posted: May 11, 2006 at 1:46 PM
Bump
Posted By: xtremej
Date Posted: May 11, 2006 at 3:43 PM
That where I always grab them, its difficult to get to though.
-------------
Posted By: zues79
Date Posted: May 11, 2006 at 5:59 PM
well i guess i have no choice then i alread got it to lock with the remote but i still need to cut the unlock wire..
Do i need to hook up the acc wire up to anything??
Posted By: cntrylvr79
Date Posted: May 13, 2006 at 9:31 PM
Don't think you HAVE to hook the accy wire up. Though it might be necessary if you want to change any of the default programming options.
-------------
Cause I'm So white and nerdy...
First Class Certi-fried installer
|