Urgently need 07 Escalade Wiring diagrams
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=79386
Printed Date: May 09, 2025 at 3:40 AM
Topic: Urgently need 07 Escalade Wiring diagrams
Posted By: escalade007
Subject: Urgently need 07 Escalade Wiring diagrams
Date Posted: June 20, 2006 at 7:50 PM
Hi, I've been unable to locate any 07 Escalade electrical wiring diagrams. Can someone tell me where these are available from? Also, does anyone know where the starter/kill wire switch is? Thanks
Replies:
Posted By: chungo
Date Posted: June 20, 2006 at 8:32 PM
| 12volts | RED / white (2A) | + | ignition harness | | Notes: For high current 12V, use RED / black (60A) and RED / black (60A) at the fuse box, black 40 pin plug, pins F1 and E3, or go to the battery. | | Starter | white | + | ign harn or BCM, lt. grn plug, pin 4 | Notes: Starter is positive trigger thru a 1300 ohm resistor.
The BCM (Body Control Module) is to the left of the steering column.
See DirectFax document 1605 for remote start interface information. | | Second Starter | N/A | | | | Ignition | pink | + | ign harn or BCM, lt. grn plg, pin 14 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Second Ignition | N/A | | | | Third Ignition | N/A | | | | Accessory | brown | + | ign harn or BCM, lt. grn plg, pin 21 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Second Accessory | N/A | | | | Keysense | pink | + | ign harn or BCM, lt. grn plug, pin 2 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Power Lock | see notes | | | Notes: To lock/unlock the driver door go to the driver door module or motor in the door and 5wi the tan (lock) and purple (unlock) motor wires.
To lock/unlock the passenger door go to the passenger door module or motor in the door and 5wi the tan (lock) and gray/black (unlock) motor wires.
To lock/unlock the rear doors use lt. blue (+) and white (-) at the BCM, gray plug, pins 7 and 9.
The BCM (Body Control Module) is to the left of the steering column. | | Power Unlock | see power lock notes | | | | Lock Motor | gray | 5wi | fuse box, black 14 pin plug, pin B4 | | Unlock Motor | purple | 5wi | DDM, brown 16 pin plug, pin 8 | | Notes: The DDM (Driver Door Module) is in the driver door. | | Parking Lights+ | brown (L), brown (R) | + | underhood fuse box, blk 30 pin plug | | Parking Lights- | lt. blue | - | switch or BCM, natural plug, pin 8 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Hazards | white | - | switch or BCM, lt. grn plug, pin 19 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Turn Signal(L) | lt. blue/wht (F), yel/blk (R) | + | BCM, brown plug, pins 4 and 1 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Turn Signal(R) | dk blu/wht (F), dk grn/wht (R) | + | BCM, blk plg, pin 5; brn plg, pin 2 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Reverse Light | dk. blue | + | BCM, natural plug, pin 22 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Door Trigger | see notes | - | see notes | Notes: The LF door is gray/black at the DDM, brown 16 pin plug, pin 13. The RF door is BLACK/ white at the PDM, brown 16 pin plug, pin 13. The LR door is lt. blue/black at the BCM, pink plug, pin 15. The RR door is lt. GREEN/ black at the BCM, pink plug, pin 14. Use all four wires and diode isolate each.
The DDM (Driver Door Module) is in the driver door.
The PDM (Passenger Door Module) is in the passenger door.
The BCM (Body Control Module) is to the left of the steering column. | | Dome Supervision | gray | + | BCM, natural plug, pin 5 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Trunk/Hatch Pin | pink/black | - | BCM, pink plug, pin 12 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Hood Pin | pink/black | - | pin sw or BCM, black plug, pin 17 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Trunk/Hatch Release | pink (glass), gray (gate) | - | BCM, pink plug, pins 24 and 13 | Notes: Meter these wires while opening the liftglass or liftgate from the handle on the rear liftgate.
The BCM (Body Control Module) is to the left of the steering column.
On vehicles with the power liftgate, use dk. GREEN / WHITE (-) at the switch in the overhead console. | | Power Sliding Door | N/A | | | | Factory Alarm Arm | | | | | Factory Alarm Disarm | lt. green | - | DDM, brown 16 pin plug, pin 4 | Notes: Meter this wire while turning the key in the driver door key cylinder.
The DDM (Driver Door Module) is in the driver door. | | Disarm No Unlock | with ignition and Passkey | | | | Tachometer | NOT pink, brown, or black | ac | any ignition coil or fuel injector | | Wait to start | N/A | | | | Brake Wire | lt. blue/white | + | switch or BCM, brown plug, pin 6 | Notes: Meter this wire while pressing the brake pedal with the ignition on.
The BCM (Body Control Module) is to the left of the steering column. | | Parking Brake | lt. blue | - | switch or BCM, brown plug, pin 16 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Horn Trigger | tan | - | switch or BCM, brown plug, pin 18 | | Notes: The BCM (Body Control Module) is to the left of the steering column. | | Memory Seat 1 | orange | + | switch or DDM, blk 26 pin plg, pin 5 | Notes: Memory seat 1 is positive trigger thru a 2260 ohm resistor. Memory seat 2 is positive trigger thru a 4260 ohm resistor.
The DDM (Driver Door Module) is in the driver door. | | Memory Seat 2 | same as memory seat 1 wire | + | | | Memory Seat 3 | N/A | + | |
 | Interface Module: | Category:
Immobilizer Bypass | Required:
Yes | Type:
PASS-Key III+ | | Part #: 556UW | | Alternate Part1 #: DesignTech 20402 | | Alternate Part2 #: DesignTech 29402 | | Notes: Standard on all models. |
| Smart Starter Kill Relays: | Relay Type:
Starter Relay | Location:
Engine compartment fusebox, Driver side | | Part #: 6404A |
|
Posted By: escalade007
Date Posted: June 20, 2006 at 9:45 PM
Does a schematic exist of the electrical?
Posted By: integratyper934
Date Posted: June 20, 2006 at 10:24 PM
the car runs on a lan system what exactly are you trying to do i heard some things about if you disconnect the radio youll have some problems. i know the factory overhead cant be used with an aftermarket head unit. what are u trying to accomplish?
Posted By: escalade007
Date Posted: June 21, 2006 at 2:33 PM
I'm trying to obtain information as to how to hook up equipment to it. One local dealer has given a story that he needs electrical schematics as he can't find the starter/kill switch to hook up a gps locator such as thewitness.net.
Posted By: integratyper934
Date Posted: June 21, 2006 at 2:50 PM
a dealer needs schematics??? what is it a contacted lo jack installer or soemthing
Posted By: escalade007
Date Posted: June 21, 2006 at 3:05 PM
If you visit the website it gives you all the details. It's more advanced the lojack. You're supposed to be able to disable the car from starting via the gps. All I know is I've heard a bunch of excuses that the escalade is very electric and complicated.
Posted By: bdl666
Date Posted: June 21, 2006 at 4:27 PM
This is what chungo posted. Just in its original form so you can print it. https://directechs.com/directwire/print.asp?action=select&yr=6216&product=Remote%20Start ------------- ieSpell rocks.
Posted By: escalade007
Date Posted: June 22, 2006 at 11:20 PM
Here's a good question. My dealer is trying to install the viper in the 07 escalade. Since the control module that controls door locks etc is not avail. for another 60-90 days for 07 model according to directed and 06 model won't work, he hard wired each of the door locks. Only the passenger door locks seem to work. Anyone have thoughts as to why?
Posted By: escalade007
Date Posted: June 23, 2006 at 10:23 PM
Problem solved.. only have to wait for a module for kill/starter to come out.
|