Aux 2 output not activating window module
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=79471
Printed Date: October 31, 2025 at 4:47 AM
Topic: Aux 2 output not activating window module
Posted By: thym8scallmet
Subject: Aux 2 output not activating window module
Date Posted: June 22, 2006 at 4:26 PM
I'm having a problem with my 99 grand prix. I have a Delta 5005 Remote start that I have had for a few years and it works perfectly. I recently installed window modules for both up and down. I have the up hooked to the starter disable and it works great. I want to use my accessory 2 option to roll down the windows, but when I hook the wire up to the accessory 2 wire and activate it, nothing happens. I know that the module works, because when I ground it, the windows go down. I have put a meter on the acc 2 wire to test it and at a setting of .2 dc volts on the meter, It shows back .631 when activated. I have tried pulsed, latched, and timed. I'm at my witts end here guys. Please help me! Thanks
T ------------- Thanks
T
Drive it like you rented it!
Replies:
Posted By: captainzab
Date Posted: June 22, 2006 at 9:02 PM
If your saying that your window goes down when you ground the input wire, then your Aux 2 output wire needs a relay.
Or your Aux 2 output wire doesnt work?
Posted By: olioli
Date Posted: June 24, 2006 at 12:41 AM
try using a timer pulse sender. you just need to send a negative pulse to activate it . you can be able to adjst the necesary time also, to keep the wnidows module down. ------------- xxx
Posted By: bjordet
Date Posted: June 26, 2006 at 2:11 AM
What source are you using for the roll up feature? If you are using the (-) out for the ignition kill that may be your trouble. Some alarm ignition kill outputs go to ground and stay there when armed. This will be giving your window module a constant ground for the roll up circuit when armed and won't allow you to activate the roll down at the same time. Have you tried the aux 2 feature when the alarm is disarmed? Just a thought.....sometimes it is the simple stuff that causes the most coconut scratching! 
Posted By: wentworth007
Date Posted: July 12, 2006 at 11:06 PM
like captain said you need a relay to get enough ground current to activate the module.
Posted By: thym8scallmet
Date Posted: July 13, 2006 at 12:20 AM
Well I may vary well need a relay. And I have tried wiring one several times. I have checked the outputs from the alarm its self, everything seems fine. I have tried to hook it up by its self with out the roll up moduels, I have hooked it up to aux 1, which is the trunk release, and it works being hooked up there. When i ground the modules while they are not hooked to the alarm, they work... I just think its wierd that I am getting a signal from aux 2 and its not activating the roll down modules. If any of you know how to wire the relay, please post it here. Thanks T ------------- Thanks
T
Drive it like you rented it!
Posted By: bbtaco
Date Posted: July 13, 2006 at 5:42 AM
Have you tried using AUX 2 for the trunk pop?
To increase the strength of your (-) AUX signal using a relay.
86 Fused 12VDC constant
85 (-) From alarm AUX 2
87 Chassis ground
30 (-) output to module
87A Not used
Posted By: thym8scallmet
Date Posted: July 13, 2006 at 3:28 PM
Actually, no I have not tried aux 2 for the trunk pop, but I will.. Ill also wire a relay the way you have shown here, but I think I tried it that way. Either which way, if this dosen't work, I think i'm going to give up on this alarm, and call that channel a lost cause.
-------------
Thanks
T
Drive it like you rented it!
|