impreza dome light
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=83282
Printed Date: May 03, 2024 at 6:30 AM
Topic: impreza dome light
Posted By: spaspecker
Subject: impreza dome light
Date Posted: September 24, 2006 at 3:34 AM
hi guys - just looking for a bit of advice regarding my wrx my94 impreza.
I have an avital maxx1 fitted and would like the dome light to come on when I kill the alarm, and then stay on until I turn the ignition key. As far as I am aware, the maxx1 does not have a dome light output, just a wire that connects to the dome light circuit to let it know when a door is open. I've done an extensive search of these forums but cannot find an answer. Any help would be much appreciated.
Replies:
Posted By: spaspecker
Date Posted: September 25, 2006 at 10:51 AM
anyone?
Posted By: swamprat323
Date Posted: September 25, 2006 at 11:23 AM
you have dome output the 10 pim harness pin 8 green wire, it tied into the door trigger.
the us impreza shows a dome but the UK modle dont.
us model
| DOOR TRIGGER|RED / black |- |near dash light |
| DOME SUPERVISION|use door trigger | | |
UK model
DOOR TRIGGER|yellow |- |driver kick panel |
| DOME SUPERVISION| | | |
its blank
Posted By: spaspecker
Date Posted: September 26, 2006 at 4:29 PM
according to the avital brochure and the installation instructions, the MAXX1 does NOT have dome light supervision output, the MAXX2 and MAXX3 have. The MAXX1 has a green wire as you say, but this is only the neg trigger to detect a door open - someone can correct me if I'm wrong.
What I want to do is rig up a system where the neg unlock trigger/pulse will switch on the domelight, which in turn will switch off when I start the car.
somebody help please!!!
Posted By: spaspecker
Date Posted: September 28, 2006 at 11:14 AM
bttt
Posted By: swamprat323
Date Posted: September 28, 2006 at 11:47 AM
yea i saw the install guide it said it was for dome too, but that dotn mean it a miss print.
anyways can use a DEI 528T pulse timer. it a timer u set form 1- 90 secs. it wont shut off when u turn ign off, just let it run out.
Posted By: bryantobando
Date Posted: September 29, 2006 at 11:02 AM
whats the diagram for that alarm?
Posted By: spaspecker
Date Posted: September 30, 2006 at 1:01 PM
the wiring diagram I have is PDF - PM me and I'll try to mail it you
Posted By: swamprat323
Date Posted: September 30, 2006 at 8:36 PM
avtial maxx 1 istall guide is in the downlaod section
Posted By: spaspecker
Date Posted: October 01, 2006 at 5:32 AM
just checked out the downloads but I couldn't find the maxx1 as I wanted to compare the install notes - every other avital is there though I think it may have another name in the states, I'm not sure
Posted By: spaspecker
Date Posted: October 14, 2006 at 3:53 PM
what if I were to add a timer to give me, say, a 10 minute 'pulse' on disarm - effectively fooling the circuit into thinking it was permanent? would it then be possible to have the light go out when the ignition was turned on?
Posted By: spaspecker
Date Posted: October 17, 2006 at 1:10 PM
can't be done then - anyone?
|