Print Page | Close Window

Wiring Diagram

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=8439
Printed Date: August 06, 2025 at 5:56 AM


Topic: Wiring Diagram

Posted By: stevepara
Subject: Wiring Diagram
Date Posted: January 22, 2003 at 7:47 AM

I am in need of a wiring digram for a pontiac transport montana extended, with keyless entry. need to install auto alarm with auto start.

thank you in advance

steve

stevesnap@hotmail.com




Replies:

Posted By: 10nesne1
Date Posted: January 22, 2003 at 9:03 AM

Pontiac

Montana

1998-2002

Remote Starter  Wiring Colors and Notes

Function

 

 

Vehicle  Color

Location

Start:

 

 

YELLOW

IGNITION SWITCH HARNESS *

Ignition  #1:

 

 

PINK

IGNITION SWITCH HARNESS

Ignition #2:

 

 

WHITE

IGNITION SWITCH HARNESS (PCM)

Ignition  #3:

 

 

N/A

****

Accessory:

 

 

ORANGE

IGNITION SWITCH HARNESS (HEAT/AC) **

Brake  Light:

 

 

WHITE (+)

AT SWITCH ABOVE BRAKE PEDAL

Tach  Signal:

 

 

WHITE

AT POWERTRAIN CONTROL MODULE

Parking Lights:

 

 

BROWN (+)

AT HEADLIGHT SWITCH

Headlights:

 

 

YELLOW (+)

AT HEADLIGHT SWITCH

OEM Alarm  Disarm:

 

 

GREEN/ BLACK (-)

16 PIN CONNECTOR IN DR. KICK PANEL

OEM Alarm  Arm:

 

 

N/A

SEE NOTES BELOW **

Diesel  Glow Plug:

 

 

Clutch  Bypass Wire:

 

 

Notes:

 ***Equippes with transponder anti-theft system - Use Universal Alarm Bypass Module following for "Transponders." ** See Installation Note #233 GM High Current Ignition if equipped with rear heat. ****All DesignTech remote starters except the 2xx22 have an ignition 3 output - it is the WHITE/ black in the 'control harness.' This wire will be used to control the anti-theft bypass module.

Pontiac

Montana

1998-2002

Alarm and Keyless  Entry Wiring Colors and Notes

Function

 

 

Vehicle  Color

Location

Constant  +12 Volts:

 

 

RED & RED

IGNITION SWITCH HARNESS

Starter  Kill:

 

 

YELLOW

IGNITION SWITCH HARNESS *

Ignition  +12 Volts:

 

 

PINK

IGNITION SWITCH HARNESS

Dome  Lights/Superv:

 

 

GRAY/BLACK (-)

AT BODY CONTROL MODULE ***

OEM Horn:

 

 

BLACK (-)

STEERING COLUMN HARNESS

Power  Lock:

 

 

RED / BLACK (-)

AT BODY CONTROL MODULE ****

Power  Unlock:

 

 

WHITE

AT BODY CONTROL MODULE ****

Trunk  Release:

 

 

N/A

Alarm  Input Wire:

 

 

GRAY/BLACK (-)

AT BODY CONTROL MODULE ***

Notes:

*** BCM Is Located To The Right Of The Glove Box. **** Negative Door Lock System.



Posted By: stevepara
Date Posted: February 05, 2003 at 7:49 AM
Thank you for a rapid response, are there any resistors that need to be used, and would you know where the wire for the electric sliding door is, would like to use it on chsnnel 3 of alarm.



Posted By: PLAYER69
Date Posted: February 05, 2003 at 8:46 AM

Sliding door is lt.blue in the overhead console - pulse.

No resistors are required.

This van has passkey3.




Posted By: HVRA
Date Posted: February 05, 2003 at 9:25 PM

i need the conections for honda civic 89  for install an alarm. i wonder if you help me ..   tanks




Posted By: PLAYER69
Date Posted: February 05, 2003 at 9:37 PM
Hvra start a new topic and someone will likey reply.


Print Page | Close Window