2000 grand am autopage 725 Locks

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=84657
Printed Date: June 15, 2024 at 7:45 AM

Topic: 2000 grand am autopage 725 Locks

Posted By: chuckles_1205
Subject: 2000 grand am autopage 725 Locks
Date Posted: October 26, 2006 at 12:04 AM

I have been looking at how to setup the locks on my wifes car and from looking at this webpage

Link

It seams like I would go with the top diagram to get that to work is that correct, also I am trying to figure out on the alarm it has 2 wires Negative door switch sensing input and Positive door switch sensing wires I am trying to find where those go and how to wire them any answers on that.
And one final note, It says that I need to hook up a wire for Neutral Safety Switch Inupt I am wondering if anyone has delt with that.

Another then that I am ready to start working on this.

Replies:

Posted By: Hymer
Date Posted: October 26, 2006 at 12:19 AM

Yep locks are correct... your triggers should be neg... so hok the pos door trig wire from the alarm to +12 v constant.. [I belive] thats how astro does them...

-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair

Posted By: chuckles_1205
Date Posted: October 26, 2006 at 7:23 AM

Well I am wondering wouldn't the bottom digram be correct in this case, becuase the thought the switches are on relays.

Posted By: chuckles_1205
Date Posted: October 26, 2006 at 4:53 PM

Ok I have figure out the locking wires but I am still stumped on the door triggers. So I have +12 and a negative wires but the door trigger is negative so what am I supposed to do about that.

Posted By: Hymer
Date Posted: October 26, 2006 at 5:14 PM

hook the neg trigger out of the alarm to your door triggers [diode isolate] and then take the positive trigger from the alarm unit and hook it to 12v constant. if that doesn't work then leave it disconnected... That is how the door triggers work on the rs/alarm units I install... it's compatible with all types of switching that way.... Good luck!

-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair

Posted By: chuckles_1205
Date Posted: October 26, 2006 at 7:41 PM

Really sweet!

I have one more quick qustion about the GMBP

I am stumped on the brown wire, it reads "Connect to (-) ground output when running wire of remote start system" what does that actually mean?

Thank you for your help.

Posted By: Hymer
Date Posted: October 26, 2006 at 9:27 PM

the rs sends a ground out put when it's in operation... look at your rs manual... may be called a status wire... just needs to be (-) when the rs is on.... (turns on the gmbp)

-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair

Posted By: chuckles_1205
Date Posted: October 26, 2006 at 10:52 PM

Ok I cannot for the life of me find that wire on it.

posted_image

So here is my diagram for the remote start.

If you can't see it good I have the full scan here.

Thanks a million guys I am just stumped on this one!

Posted By: chuckles_1205
Date Posted: October 27, 2006 at 7:13 AM

anybody?

Posted By: Twelvoltz
Date Posted: October 27, 2006 at 10:38 AM

H10 Connector, Yellow wire, -3rd ignition output. This wire will provide a negative output through the entire remote start sequence. Connect this to the GMBP brown wire. This lets the GMBP know when to send the information to the vehicle.

Posted By: chuckles_1205
Date Posted: October 28, 2006 at 1:01 AM

Ok who is the Smart *** at GM putting to Pink wires in the wiring bundle?? When I am checking with my Multi meter for the pink ignition wire am I suppose to see a spike in electric?