Bulldog 200b, gmsl, 06 Silverado

Trying to install a Bulldog 200B + GM-SL into a 06 Silverado with little luck. This is the first time I have ever tried to install a remote starter. Here is a short over view and issues:

GM-SL:
Connector 1 is straight forward on wiring.
   Issue: Plug in connector while holding program button, LED light does not "flash" even after 5 min of holding program button. Why?

Connector 2: The pink and pink/black wires do not get used as I have passlock 2. Am I correct? Also where does the white wire (- output door trigger)Hook to?

Bulldog:
    Do I have to use a hood pin switch? Would prefer to not.
    Ther is one wire marked as "(-) 200ma Programmable Output Dual Pulse Door unlock Output". Do I use this wire if so where? I was assuming the GM-SL controlled the door locks.

That's it for now, the more I dig into this the more I should have paid someone to do it.

CHEVROLET / SILVERADO / 2006 / Remote Start
[PRINT THIS PAGE]

12volts red (40A), red (40A) + ignition harness Starter yellow + ignition harness Second Starter N/A Ignition pink + ignition harness Second Ignition white + ignition harness Notes: To avoid the check engine light from coming on and possible damage to the automatic transmission, the second ignition in this vehicle MUST be powered when adding a remote start system. Third Ignition N/A Accessory orange + ignition harness Second Accessory brown + ignition harness Keysense lt. green - ignition harness Power Lock use Directed module 1700G Notes: If interface module is not available, refer to DirectFax document 1601. On base model trucks, the interface module is not necessary. Instead, the lock wire is lt. blue (-), pin B5, and the unlock wire is white (-), pin B10. They are in the lt. blue plug at the BCM. Power Unlock see power lock Lock Motor gray 5wi driver door module in door Unlock Motor tan 5wi driver door module in door Parking Lights+ brown + driver kick panel Parking Lights- gray/black - switch or BCM, brown plug, pin B2 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Hazards white - hazard switch Turn Signal(L) dk. green + turn signal switch Turn Signal(R) lt. green + turn signal switch Reverse Light lt. green + BCM, black plug, pin F Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Door Trigger gray/black (D), BLACK/ white(P) - each door module in each door Notes: On base model trucks, the door trigger wires are in the lt. blue plug at the BCM, pins B4 and A5. On 4dr trucks, the LR door trigger is lt. blue/black, pin A3, and the RR is lt. GREEN/ black, pin A2. They are in the purple plug at the BCM. Use all wires and diode isolate. The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Dome Supervision gray/black + BCM, black plug, pin E Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Trunk/Hatch Pin N/A Hood Pin N/A Trunk/Hatch Release N/A Power Sliding Door N/A Factory Alarm Arm arms on lock with door open Factory Alarm Disarm lt. green - driver door module in door Disarm No Unlock see factory alarm disarm Tachometer white ac instrument cluster, pin A5 or PCM Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. On gas models, the tach wire is in the green plug, pin 10. On diesel models, the tach wire is in the black 58 pin plug, pin 55. On hybrid models, the tach wire is in the green plug, pin 35. For tach can also go to any of the ignition coils or fuel injectors and use the wire that is NOT pink, black, or brown. Wait to start dk. blue - instrument cluster, pin A2 or PCM Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. The wait to start wire is in the black 58 pin plug, pin 16. On the remote start, make sure to program the Accessory State During Wait To Start to ON. Brake Wire white + brake pedal switch Parking Brake lt. blue - switch or BCM, lt. blu plug, pin A7 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Horn Trigger BLACK / YELLOW to black - switch or BCM, gray plug, pin B9 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Memory Seat 1 red + driver door module in door Memory Seat 2 pink + driver door module in door Memory Seat 3 N/A + Interface Module: Category: Immobilizer Bypass Required: Yes Type: Passlock II Part #: 1100F Alternate Part1 #: 1100X Alternate Part2 #: 556LW Alternate Part3 #: 555LW Alternate Part4 #: DesignTech 20402 Alternate Part5 #: DesignTech 29402 Notes: Not required if using the combo interface module. The Passlock II wire colors are yellow, black, and RED / white (not used). When using the 1100F or 1100X, a software change to 1100GM is needed. Interface Module: Category: Combo Interface Required: Yes Type: Data Bus Part #: 1700G Alternate Part1 #: 457GW Notes: Smart Starter Kill Relays: Relay Type: Starter Relay Location: Engine compartment fusebox, Driver side Part #: 6402A This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.

-------------
Hotttunes - Bassman
Installer since 1976
Too many years experience
Cookeville, TN.

Professionally Installed With Pride

Anything worth doing is worth doing to the BEST of your ability!

what i wonder is why you are wanting to put a $40 rs unit on your new 25K vehicle?

-------------
South Side Audio
2501 S. High St
Columbus, OH 43207