alarm won’t stop
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=87057
Printed Date: May 03, 2024 at 7:03 AM
Topic: alarm won’t stop
Posted By: doggy626
Subject: alarm won’t stop
Date Posted: December 12, 2006 at 2:23 AM
Hello people. This is my first post so any mistakes i make, just point them out. I have a1999 Chevy Silverador that came with an alarm. It's a code arlarm Elite 2100. The Problem is that after the alarm is set, it goes off by itself after about a minute. Keeps going until i use my remote to shut it off. I've had my truck for 2yrs. now,and it was working fine untill now.Didn't get manual for it so i don't know what it could be. So if any one can push me in the right direction, it would be a big help to me. And also i'm want to find out how to program my alarm again because before it would lock my doors whenever i armed it. It unlocks when disarmed but won't lock. If i'm correct that would be in the programming right? Thanx luidog626
-------------
luilui
Replies:
Posted By: Fastlearner
Date Posted: December 12, 2006 at 4:58 AM
If you don't have to much experience with alarms, I would just take it to the nearest shop and have them check it out. Usually It will only cost around $30 or so to have someone check it out.
Posted By: doggy626
Date Posted: December 12, 2006 at 1:07 PM
I do have car audio experience in installations but in alarms i have very little experience. About my alarm going off by itself i don't have a clue what it could be,but i have programmed alarms before. I only need the manual for it or if anyone could help me out with one. Thanx for the reply fastlearner. Maybe i should take it somewhere to have it checked out, that is if i get no replys.
-------------
luilui
Posted By: 05gt
Date Posted: December 12, 2006 at 1:08 PM
what do you want to program, is it the shock sensor going off does it go off every hour on the hour, need a bit more info
Posted By: doggy626
Date Posted: December 12, 2006 at 1:20 PM
After alarm is set, it starts going off by itself after about a minute. It will stop for a moment and then it starts again and again until i use my remote to turn it off. The thing i want to program is the door locks. Before it would lock my doors whenever it sets itself on but know it doesn't. Its a code alarm elite 2100.
-------------
luilui
Posted By: mart.p
Date Posted: December 12, 2006 at 3:14 PM
have you checked the hood pin switch. it may be broken. ------------- mart
Posted By: Fastlearner
Date Posted: December 12, 2006 at 3:28 PM
Could it be a dome light issue if the door trigger is hooked up to the domelight. Maybe it has a delay in it but if the domelight stays on for a little bit it might be reading as the door is open thus setting off the alarm.
Posted By: mart.p
Date Posted: December 12, 2006 at 3:45 PM
just try disconecting the the unit if you can find it .it may reset its self.
-------------
mart
Posted By: doggy626
Date Posted: December 12, 2006 at 4:24 PM
I think i will disconnect it and connect it back. Hopefully it does reset itself. Thanx. ------------- luilui
Posted By: splaudio
Date Posted: December 12, 2006 at 5:49 PM
sounds like to me it somehow reset its self. reason being the shock sensor is really low and could be digital and the doors are locking like they were. give code a call they might be of more help...
Posted By: doggy626
Date Posted: December 12, 2006 at 6:31 PM
Yea, i think the best thing to do is to call code. Anyways, thanks for the help.
-------------
luilui
|