06 Tacoma alarm/remote start

Hi all, just wondering if anyone has a wiring diagram for this vehicle. I had an appointment to have a Clifford Matrix RSX50.5 installed, but I removed a compustar RS unit from my wife's old car and found all of the wiring just wrapped and taped around the wires that they were spliced into. nothing but tape! To say I was a little upset is an understatement. I cancelled the appointment and telling the guy behind the counter that he/they were a bunch of hacks made me feel better. But now I am gonna do this myself. I was heavily into car audio years ago and feel confident that I can do this. I just can't find a wiring diagram.
Thanks,
Larzzzz

Wich model compustar....I can send you some COOL info. tell me what the brain # is.

-------------

It is a CM-4200 v.2 with 4 button remotes. Will this thing be doing tricks when I'm done messing with it? Thanks for the offer, I hope it works.

Thank God I scrounged around some more and found wiring Diagram on what was page 32 of this forum....it wasn't in the d/l section. Life is good

Wire/Function	CM4200	Colour	Location/Description	Polarity
12 VOLTS	RED & RED / WHITE(CN1)	WHITE/ blue	Ignition switch harness	+
IGNITION	GREEN (CN1)	Blue / YELLOW	Ignition switch harness	+
IGNITION 2	BLUE (CN1)	BLACK/ red	Ignition switch harness	+
ACCESSORY	WHITE (CN1)	Runs with ignition wire
STARTER	YELLOW (CN1)	BLACK/ white	Ignition switch harness	+
STARTER 2	RED / BLACK (CN2) + Relay	GREEN/ black	Ignition switch harness	+
KEY SENSE		GREEN/ black	Ignition switch	-
TACH SIGNAL	YELLOW/BLACK (CN3)	See notes
On the 2.4L and the 2.7L engine, there are 2 coils on the left front of the engine. Use the BLACK/ BLUE or BROWN / YELLOW for a 2 cylinder signal. On the 3.4L engine there is a coil per cylinder. Use the wire opposite from the BLACK/ RED at any of the coils. With any of the engines you can also find a BLACK tach reference at pin-15 of the 26-pin connector on the ECM behind the glovebox.
FUEL INJECTOR		Opposite from BLACK/ red	At any injector on engine	AC
LOCK	BLUE/BLACK (CN4)	Blue/white	In driver's kickpanel	-
UNLOCK	BLUE (CN4)	GREEN/ black (double pulses)	In driver's kickpanel	-
DOORPIN	RED / WHITE(+) or RED(-) (CN3)	SEE NOTES
GREEN (driver's door), GREEN / WHITE (passenger door), YELLOW /GREEN (rear doors). All 3 wires are found in a 22-pin connector on the front of the fusepanel under the dash. Isolate with 1N4001 diodes if connecting together.

-------------

BRAKESWITCH	LT.BLUE/WHITE (CN3)	Blue	At switch above brake pedal	+
PARKLIGHTS	GREEN / WHITE (+) (CN1) or (-) (CN2)	Green	Parking light switch	-
HAND BRAKE	LT.BLUE (CN3) Manual only	GREEN / WHITE	At switch on handbrake lever	-
HORN	WHITE (-) (CN2)	GREEN/ red	At steering column	-
CLUTCH SWITCH	Manuals only (see inst. Guide)	BLACK/ white	At switch on top of clutch pedal	TYPE 1
DRIVER WINDOW UP		Blue / YELLOW	At master window switch	REV POL
DRIVER WINDOW DOWN		Blue/green	At master window switch	REV POL
PASSENGER WINDOW UP		RED / black	At master window switch	REV POL
PASSENGER WINDOW DOWN		RED / green	At master window switch	REV POL
HEADLIGHTS		RED / blue or RED / green	At light switch harness	-
REVERSE LIGHTS		RED / black	In driver's kickpanel	+
DIMMER		WHITE/ green	At harness behind dimmer switch	+
VSS WIRE		GREEN/ orange	At ECM behind glovebox
The GREEN/ ORANGE vss wire is located on the ECM behind the glovebox. On the 2.4L and 2.7L, it's at pin-8 of the 22-pin connector. On the 3.4L, it's at pin-12 of the 28-pin connector.

Vehicle Notes	N/A
Additional Notes	WHEN PROGRAMMING THE PATS TOYOTA THE BLACK WIRE FROM PATS TOYOTA MODULE TO GROUND FIRST. AFTER THE BLACK WIRE IS GROUNDED GROUND THE BLUE KEY SENSE WIRE ON THE IGNITION BARREL. DO NOT GROUND AT THE SAME TIME.

 

You see on this diagram it lits the wire for the brain, and the color and location of the wire on your truck.....put the 2 together.

-------------

Thanks Kar for the wiring diagram, but which vehicle is it for? If it's the Tacoma, it is referencing engine sizes that aren't in this truck. I did find one for the 06 Tacoma already, but thanks for your reply. The Compustar I ranted about is going to go in the wife's new car, a 2000 Buick LeSabre.

Will the dei 555xw work for an 06 tacoma? I Really don't like the thought of having to use a key to install in a bypass module.
Thanks
Larzzzz

A 555x will not work....

-------------
Mike M2
Tech Manager
CS Dealer Services

An XK05 PKT2 firmware from bypasskit.com wires right into the harness no need to bury a key.. they work great!

-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair

Thanks for the info. Unfortunately, I am not a dealer but an end user. I was gonna sign up but they want a tax ID# which I don't have Such is life......
Thanks again,
Larzzzz
Jack of all trades, master of 1

Hi all, Happy new year. I've come accross 2 wiring diagrams here for the 06 Tacoma. Could someone please tell me which is the correct one?
On this link;
https://www.the12volt.com/installbay/forum_posts.asp?tid=87353&KW=06+tacoma
KarTuneMan posted a reply to my post here, but notes reference engine sizes that aren't what I have (4.0)

On this link, there is another;
https://www.the12volt.com/installbay/forum_posts.asp?tid=83234&KW=06+tacoma

So, which is the correct one?
Thanks, and I hope we all had a New years we can remember
Larzzzz

They are both right, just have some discrepenacies between them. The first link is a Directechs and the 2nd is a Wire Magic. Use both and test with a DMM for wires and locations that differ.

-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA

tahnkyou thankyou thankyou
Happy new year
Larzzzz

I had a Clifford 50.5x rs/ alarm installed in my toyota tacoma dbl cab. Is it possible to use the factory key fob to arm and disarm the alarm while also operating the locks?
I don't care about the rs with the factory fobs, i just want a backup.

Thanks,
Larzzzz

Nope, not possible...

-------------
Mike M2
Tech Manager
CS Dealer Services