2005 montana remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=88004
Printed Date: May 03, 2024 at 5:08 PM
Topic: 2005 montana remote start
Posted By: gregkreuger
Subject: 2005 montana remote start
Date Posted: December 29, 2006 at 6:15 PM
hello, im currently installing a remote start on my montana and cant seem to find the location of the ignition harness wiring, igniton control module, i have the drawing and the igniton #1 is pink, and i see about 8 pink wires in the main bundle going across the engine, thanks in advance for any advice, greg
Replies:
Posted By: prdjr165
Date Posted: December 29, 2006 at 6:34 PM
The ignition harness is the wires coming out of the ignition switch,usually behind the dash coming down the steering column.
Posted By: gregkreuger
Date Posted: January 01, 2007 at 11:33 AM
good day, i am installing a "radiostar generation" LCD remote and so far its been trouble, i cant get the starter to engage, all the door locks work, when i press for a remote start the accessory comes on but doesnt start, i tried the turbo short run and that worked, i think my problem is with the (+) ignition input of the key cylinder to alarm, i connected this to same wire as (+) ignition output of the heavy guage harness,? not sure where to go from here, thanks in advance, happy new year. greg
Posted By: chris354
Date Posted: January 01, 2007 at 12:28 PM
On that vehicle it has pass key 3 anti theft system that has to be bypassed. See if you can put the key in the ignition dont turn it then try to rs. If it starts thats the problem.
Posted By: gregkreuger
Date Posted: January 01, 2007 at 12:37 PM
okay tried that but it still didnt start, my bypass when i start it the led goes off, my remote sends a (-) 200ma to the passkey, is this the same as ground when running?
Posted By: chris354
Date Posted: January 01, 2007 at 12:59 PM
What type of bypass are you using.
Posted By: gregkreuger
Date Posted: January 01, 2007 at 1:02 PM
I am using Platform #06 Firmware:PKG5 Passkey 3 greg
Posted By: maxcat
Date Posted: January 01, 2007 at 1:24 PM
Hi there , On that remote start there is a wire labled neutral safety switch input. If the vehicle can not be started while in gear, then just connect this wire to a ground. This wire neend to see ground before the start proccess will start.
Posted By: gregkreuger
Date Posted: January 01, 2007 at 1:39 PM
Can someone tell me what the Driver's Lock/Unlock motor's are???
Posted By: gregkreuger
Date Posted: January 01, 2007 at 2:05 PM
feeling silly, i needed to have the park brake on for the unit to start, and it starts, thanks for all your help, i love this website. onto my next challenge. greg
Posted By: gregkreuger
Date Posted: January 02, 2007 at 6:28 PM
new problem here, i cant get the remote start to unlock the doors when its running, press once disables factory alarm, press twice unlocks the all the doors, but when in remote start, it wont allow me to disable the alarm to unlock the doors, has anyone seen this before?
Posted By: chris354
Date Posted: January 02, 2007 at 7:08 PM
On that van it takes a 3.5 second pulse to unlock the doors if it has the factory alarm. I am not familer with that brand rs but some you can program the duration for the lock and unlock pulse if not you will need a timer module.
|