security lamp, 1998 gmc seirra
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=88159
Printed Date: May 02, 2024 at 4:40 AM
Topic: security lamp, 1998 gmc seirra
Posted By: wscovil
Subject: security lamp, 1998 gmc seirra
Date Posted: January 01, 2007 at 12:10 PM
im having problems with my 1998 gmc seirra P\u starting and stalling and the security lamp flashes. i tried installing a RCS and now i can not start the truck .i even tried unpugging the car starter and still not helping..any advice would greatly be appriciated!! thanks ------------- Wayne
Replies:
Posted By: chris354
Date Posted: January 01, 2007 at 12:18 PM
Did you use a theft bypass module. You need one to bypass the passlock 2 theft system.
Posted By: wscovil
Date Posted: January 01, 2007 at 12:36 PM
I Installed the starter first and then when i went to hook up the bypass module (XK06) i noticed that the wiring colors ect did not match what i had.so i thought that i could still start the truck normally until i could figure out the bypass details.the truck already had a Artic start starter and a bypass (no name on it).but it has always gave me problems when it get real hot inside the truck so i thought i would change it.i just unhooked the bypass and resoldered the wires back togather.
-------------
Wayne
Posted By: Velocity Motors
Date Posted: January 01, 2007 at 5:38 PM
Make sure that there is not another break on the wire for the Passlock wire ( use a DMM and set to continuity ).
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: wscovil
Date Posted: January 01, 2007 at 5:42 PM
jeff,do you happen to know which wire it is?also do you know if i tried to start the truck with the wire not hooked up ..would it put into some kind of security mode? thanks for your help . ------------- Wayne
Posted By: chris354
Date Posted: January 01, 2007 at 6:29 PM
There should be a yellow and a black wire that runs up to the ignition switch they are thin wires usually the yellow wire is cut into for most bypasses. If the truck get the wrong code I think you have to turn the key on for like 12 minutes then it should start as long as the wires are intact.
Posted By: wscovil
Date Posted: January 01, 2007 at 6:34 PM
ok thanks,i'll try that .
-------------
Wayne
Posted By: au5599
Date Posted: January 01, 2007 at 7:57 PM
xk06 can be an issue. What is it stamped for on the top? They can be preprogrammed for several different interfaces. Also passlock II wires are thin wires usually yellow, orange with black stripe and red with white stripe. On some they did yellow, black and white. Make sure all wires are fully intact again. Then turn on and try starting with key. If it trips security leave key on for 15 minutes and come back turn off then back on and it should start up and run. Then you need to figure out if you got the right interface program for the xk06 to work on that truck. ------------- Street Dreams Car Club
93 GRAND CARAVAN SE / Astro
Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals
2003 Chevy Suburban LT / 98 GTP
Posted By: wscovil
Date Posted: January 01, 2007 at 8:17 PM
My XK06 is PKG7. I havnt had it fully hooked up because i couldnt decipher where the wires went ..the colors that they to use ,i didnt have on mine.so i resoldered the yellow wire back togather and just unpluged the remote starter. also i tried leaving the key on for 15 mins.then i turned it off and tried to start but the sercuity light just keeps flashing and the truck just stalls .this thing is driving me crazy .:) ------------- Wayne
Posted By: au5599
Date Posted: January 02, 2007 at 8:29 AM
wscovil wrote:
My XK06 is PKG7. I havnt had it fully hooked up because i couldnt decipher where the wires went ..the colors that they to use ,i didnt have on mine.so i resoldered the yellow wire back togather and just unpluged the remote starter. also i tried leaving the key on for 15 mins.then i turned it off and tried to start but the sercuity light just keeps flashing and the truck just stalls .this thing is driving me crazy .:)
The XK06 is wrong. It will NOT work on that truck. You need it programmed for a PLXR How are the other 2 wires? either orange with black stripe and red with white stripe or black and white wires? after 15 minutes was the security light flashing? Make sure you try to start with key first, then leave the ignition on without shutting it off. Wait the 15 minutes. ------------- Street Dreams Car Club
93 GRAND CARAVAN SE / Astro
Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals
2003 Chevy Suburban LT / 98 GTP
Posted By: Velocity Motors
Date Posted: January 02, 2007 at 11:20 AM
There's still the problem of the truck not starting with the wires connected back to factory. Test the YELLOW & the WHITE wire at the Passlock connector at the key cylinder for continuity and make sure that the BLACK wire has ground at all times. Reset the Passlock if it's been tripped into long tamper mode.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: wscovil
Date Posted: January 02, 2007 at 1:53 PM
i dont have a white wire ..i only have a Yellow, orange w/black stripe and red w/ white stripe. so which two would i check? thanks ------------- Wayne
Posted By: Velocity Motors
Date Posted: January 02, 2007 at 2:18 PM
ORANGE / Black - test forGROUND
YELLOW - test for continuity
RED / WHITE - test for continuity
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Velocity Motors
Date Posted: January 02, 2007 at 2:18 PM
ORANGE / Black - test forGROUND
YELLOW - test for continuity
RED / WHITE - test for continuity
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: wscovil
Date Posted: January 02, 2007 at 7:07 PM
i left the key on and forgot about it and when i came back out the battery was dead ...so i recharged it and eveything seams to fine now ..i got the bypass installed and everything is working ....i would like to thank everybody for all the help ..this is a great site!!
-------------
Wayne
|