alarm/remote start, 99 chrysler lhs
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=88735
Printed Date: May 18, 2024 at 4:35 PM
Topic: alarm/remote start, 99 chrysler lhs
Posted By: playboy00786
Subject: alarm/remote start, 99 chrysler lhs
Date Posted: January 10, 2007 at 7:45 PM
I have a ungo/clarion alarm and remote start and i wanted to know how exactly i set up or wire a xk03 with a 99 chrysler lhs transponder along with the alarm and lock/unlock part as well.
Replies:
Posted By: Hymer
Date Posted: January 10, 2007 at 8:34 PM
Super easy, but the XK03 wont do the transponder, it;ll arm/disarm/locks/trunk.. ya ned a pkuch to do the transponder. just hook the outputs from the alarm to the wires on the xk03 and a ground when running/12v/gnd and run the data wire... ithink the firmwarev is chdl2 for the xk03 also..
-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair
Posted By: playboy00786
Date Posted: January 11, 2007 at 10:15 AM
i cant get the xk03 to lock and unlock my doors.
Posted By: playboy00786
Date Posted: January 11, 2007 at 6:56 PM
i have a ungo sr6000 and a 99 chrysler lhs and im using a xk03 w/ chdl2. It will lock but not unlock or the other way around will unlock but not lock its one or the other. Any ideas?
Posted By: playboy00786
Date Posted: January 12, 2007 at 9:09 AM
I have a ungo rs6000 and a 99 chrysler lhs and im using a xk03 for my locks and everything and i having problems getting them to lock and unlock.... well they will do one but not the other like lock but not unlock or unlock and not lock....?!?!?!
Posted By: playboy00786
Date Posted: January 13, 2007 at 1:23 PM
My car says it needs 620ohm, 900ohm, 1.6kohm, and 2.7kohm. I have only been able to find a 2.7kohm what can i do or where can i buy some?
Posted By: Twelvoltz
Date Posted: January 13, 2007 at 1:55 PM
Radio Shack will have what you need. You may have to use more than one resistor to achieve the values you require. Check this page on how series and parallel circuits affect resistor values.
Posted By: Sad, little man
Date Posted: January 13, 2007 at 7:09 PM
Parts express is a good source for electronic components. Some of their resistors can get a bit pricey, so it depends on what you're doing with them if you need to get the better quality ones. Parts express resistorsAlso, to match those resistor values without getting a resistor that matches the value exactly, you can combine them. In series, you can just add the values of resistors to get the total, for parallel, use this calculator.
Posted By: playboy00786
Date Posted: January 14, 2007 at 11:24 AM
How do i configure a relay for my trunk release. 99 chrysler lhs
Posted By: playboy00786
Date Posted: January 27, 2007 at 3:18 PM
Im understanding all of the installation except when it says use a jumper wire to start up the vehicles ignition without starting up the vehicle.....how exactly do i do this?
Posted By: prdjr165
Date Posted: January 27, 2007 at 5:04 PM
take a jumper wire and put one end on a positive source (battery)then put the other end on the ignition wire(cut away a small part of the insulation).It helps to have alligator clips on the end of the jumper wire.
Posted By: playboy00786
Date Posted: January 27, 2007 at 6:07 PM
is a jumper wire a special wire or just a wire the same gauge as the ignition wire?
Posted By: au5599
Date Posted: January 27, 2007 at 7:19 PM
hook up the remote start. Now when you go to programn the interface use a decent thickness wire. Jump on your connector for the remote start the ignition and to the 12 volt power.
-------------
Street Dreams Car Club
93 GRAND CARAVAN SE / Astro
Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals
2003 Chevy Suburban LT / 98 GTP
Posted By: playboy00786
Date Posted: January 30, 2007 at 4:57 PM
Ive got a 99 chrysler LHS and a ungo rs6000. When i activate the remote start the car will start then die a few seconds later. Sould i change the tach wire or any other ideas...Thanks
|