2003 explorer sport trac, viper 791 xv
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=89977
Printed Date: May 08, 2025 at 7:02 PM
Topic: 2003 explorer sport trac, viper 791 xv
Posted By: rnemtb
Subject: 2003 explorer sport trac, viper 791 xv
Date Posted: February 03, 2007 at 7:53 AM
good morning, does anyone know the door ajar wire isfor 2003 ford explorer sport trac is ? installing a viper 791vx with r/s also can i diode isolate the bcm wires under dashor only under hood @the fire wall. thanks george ------------- rnemtb
Replies:
Posted By: Mike M2
Date Posted: February 03, 2007 at 9:44 AM
Use the blck/blue positive in the drivers kickpanel. It will control all doors. There are no diodes needed.
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: rnemtb
Date Posted: February 03, 2007 at 11:16 AM
mike m2, am i using the purple wire H 1/7 wire for the body cotrol mod or is this for the gem wake up? blk/blue shows 12volt with key in on position. thanks for your help george ------------- rnemtb
Posted By: rnemtb
Date Posted: February 03, 2007 at 11:18 AM
i am also using directed tech tips 1093 and 1076 george ------------- rnemtb
Posted By: NowYaKnow
Date Posted: February 03, 2007 at 1:41 PM
Use the BLACK/ blue (+) for your trigger, and if you want to do the GEM wakeup use the BLACK / YELLOW or yellow/black (-) in the drivers door boot. If you just close all doors and lock with the aftermarket remote like most people will, you should never run into the problem.
Mike
Posted By: rnemtb
Date Posted: February 04, 2007 at 7:33 AM
i am installing a viper 791 xv in a 2003 explorer sport trac with a 556sw bypass module. my issue is the BLACK/ red input wire it says to connect to (-) remote start status input wire. nothing matches this description . the alarm works no problem,just need to get remote start to work. the BLACK/ red wireshows 12volts. all other wires for bypass hookedas follows black - ground yellow - not used red -12 v input blk/red - ? thanks to all for the help yesterday thanks george ------------- rnemtb
Posted By: f150fan
Date Posted: February 04, 2007 at 8:25 AM
There is a small blue wire in a 4pin harness that plugs into the back of the relay pack that houses the ignition wires. That blue wire is your status wire.
Posted By: Mike M2
Date Posted: February 04, 2007 at 10:30 AM
I never wake the GEM on Explorers and have yet to have an issue because of it. Simply connect the purple H1/7 to the BLACK/ blue in the kickpanel. It should show 12volts until the interior lights go out. Turn off the delay chirp so it doesn't give a second chirp 5 seconds after arming. Do like f150 said, the thin blue on the small plug on the satolite relay pack will go to BLACK/ red on the 556s. ------------- Mike M2
Tech Manager
CS Dealer Services
Posted By: rnemtb
Date Posted: February 04, 2007 at 7:56 PM
hooked up blue status wire. still wont remote start dont know what wire if any i do not have hooked up? programmed remote. alarm and locks still work just wont remote start.any ideas?
thanks
george
-------------
rnemtb
Posted By: another-kelly
Date Posted: February 04, 2007 at 8:58 PM
did you program the 556s to your vehicle?
Posted By: rnemtb
Date Posted: February 05, 2007 at 7:29 AM
tried with key in ignition ,programmed 556 bypass for car and still nothing. also re adjusted ring at ignition cylinder.
-------------
rnemtb
|