wiring for a 2006 suzuki grand vitara xl7
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=90215
Printed Date: May 08, 2025 at 5:05 AM
Topic: wiring for a 2006 suzuki grand vitara xl7
Posted By: shoks
Subject: wiring for a 2006 suzuki grand vitara xl7
Date Posted: February 08, 2007 at 11:20 AM
I want to install a GSM monitored immobilizing alarm, so I need the wiring diagram for the ignition etc.
Any help?
Replies:
Posted By: Twelvoltz
Date Posted: February 08, 2007 at 11:38 AM
DEI lists this for the US version:
DIRECTWIRE™ WIRING INFORMATION - SUZUKI / GRAND VITARA / 2006 / Remote Start
[PRINT THIS PAGE]
12volts wht/red (50A), wht/grn (40A) + ignition harness
Starter BLACK / YELLOW + ignition harness
Second Starter N/A
Ignition BLACK / YELLOW + ignition harness
Second Ignition N/A
Third Ignition N/A
Accessory yellow + ignition harness
Second Accessory blue + ignition harness
Keysense blue/red + ign harn or BCM, 24 pin plug, pin 3
Notes: The BCM (Body Control Module) is above the driver kick panel.
Power Lock pink/black - dr kick or BCM, 40 pin plug, pin 27
Notes: The BCM (Body Control Module) is above the driver kick panel.
Power Unlock pink/green - dr kick or BCM, 40 pin plug, pin 26
Notes: The BCM (Body Control Module) is above the driver kick panel.
Lock Motor blue/red 5wi dr kick or BCM, 15 pin plug, pin 3
Notes: The BCM (Body Control Module) is above the driver kick panel.
Unlock Motor blue 5wi dr kick or BCM, 15 pin plug, pin 8
Notes: The BCM (Body Control Module) is above the driver kick panel.
Parking Lights+ RED / yellow + driver kick or fuse box, 24 pin plug
Parking Lights- RED / blue - switch or BCM, 24 pin plug, pin 11
Notes: The BCM (Body Control Module) is above the driver kick panel.
Hazards yellow/red - switch or BCM, 40 pin plug, pin 34
Notes: The BCM (Body Control Module) is above the driver kick panel.
Turn Signal(L) GREEN/ red + driver kick or fuse box, 24 pin plug
Turn Signal(R) GREEN/ YELLOW + driver kick or fuse box, 24 pin plug
Reverse Light red + driver kick, harness to rear
Door Trigger BLACK/ org (D), BLACK/ red (P) - DKP or BCM, 40 pin plug, pins 39, 38
Notes: Use both wires and diode isolate each.
The BCM (Body Control Module) is above the driver kick panel.
Dome Supervision BLACK/ red - A pillar or BCM, 15 pin plug, pin 15
Notes: The BCM (Body Control Module) is above the driver kick panel.
Trunk/Hatch Pin common with pass. door trigger
Hood Pin N/A
Trunk/Hatch Release blue/white (unlock only) 5wi pass kick or BCM, 15 pin plug, pin 7
Notes: The BCM (Body Control Module) is above the driver kick panel.
Power Sliding Door N/A
Factory Alarm Arm pink - dr kick or BCM, 40 pin plug, pin 37
Notes: Meter this wire while turning the key in the driver door key cylinder.
The BCM (Body Control Module) is above the driver kick panel.
Factory Alarm Disarm pink/blue - dr kick or BCM, 40 pin plug, pin 36
Notes: Meter this wire while turning the key in the driver door key cylinder.
The BCM (Body Control Module) is above the driver kick panel.
Disarm No Unlock see factory alarm disarm
Tachometer NOT blk/wh, blk/org or blu/blk ac any ignition coil or fuel injector
Wait to start N/A
Brake Wire GREEN / WHITE + brake pedal switch or driver kick
Parking Brake RED / black - switch or BCM, 40 pin plug, pin 8
Notes: The BCM (Body Control Module) is above the driver kick panel.
Horn Trigger blue - switch or BCM, 40 pin plug, pin 15
Notes: The BCM (Body Control Module) is above the driver kick panel.
Memory Seat 1 N/A
Memory Seat 2 N/A
Memory Seat 3 N/A
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Transponder
Part #: 556UW
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes:
Smart Starter Kill Relays: Not Available
warning
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
-------------
Installer, IT support, and FFL. I need less hobbies.
|