561t setting wait to start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=90533
Printed Date: May 07, 2024 at 1:20 AM
Topic: 561t setting wait to start
Posted By: megatfauzi76
Subject: 561t setting wait to start
Date Posted: February 15, 2007 at 8:19 PM
Hai, Im using 561T with my factory alarm..To activate the 561T..I need to press the lock button 3 times within 3 second at my transmitter... Im using automatic car..so no need to wait before i can start my engine...In others words, no need to wait the check engine light turn off than I can start my car just like diesel engine and some others car..Becuase in my car manual also, they didnt said I need to wait before start the car.. My problem now...Once I activate my 561T...i need to wait about 15 second before it start cranking my engine... How i can reduce this wait to start duration...I plan If can...After I activate my 561t..5 second after that it start cranking my engine... CAn anyone help me...I cant use bitwriter, becuase 561T is add on to my factory alarm...Also, I dont understand from the 561T manul book...to do the setting..for default setting PRESS CHANNEL 1...other setting, PRESS CHANNEL 2.. What does it mean? I dont have a channel at my alarm...My transmitter only have 2 button..lock and unlock.. Can anyone guide me? Thank you
Replies:
Posted By: kgerry
Date Posted: February 16, 2007 at 8:40 AM
ahhh, not being psychic... what type of car is it??? Channel 1 Channel 2 refers to the lock/unlock buttons on your transmitter ------------- Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: Twelvoltz
Date Posted: February 16, 2007 at 10:29 AM
Are you sure you have the correct manual for the 561T? The 561T does not include remote controls, it is just an add on piece. To change options, press lock on your door, when the unit sees a pulse on the activation wire it will change the options. If your vehicle is not a diesel then there is no need to have the wait to start timer option on.
To change this option:
Ignition on then off
Press the programming button 13 times, holding the button in on the 13th press (this is option 12 of the menu)
Press lock on the door until the LED on the brain illuminates solid, not blinking.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: megatfauzi76
Date Posted: February 20, 2007 at 7:07 PM
Thanks for reply.. My is add on remote start...To start my car...I need to press lock button on my transmitter 3 times I try from what twelvolty suggest....But nuthhing hapeen..still like previous setting.. Can you guide me more detail? Really appericiate it..Mine 561T.. Thank you
Posted By: Twelvoltz
Date Posted: February 20, 2007 at 8:35 PM
The installation manual can be downloaded here. Take a look at pages 26 and 27, it gives the same instructions as I posted but in much greater detail, and lists all of the options available to that unit. ------------- Installer, IT support, and FFL. I need less hobbies.
Posted By: megatfauzi76
Date Posted: February 20, 2007 at 11:00 PM
Can u correct me if Im wrong..This is what I understand from the manual... To activate my remote start..I need to press my lock button 3 times... Let said I want to set FEATURES NUMBER 7 ( short run turbo timer )...I want my engine turbo timer run for 10 minute... From what i understand from the manual...This is what i should do( correct me if Im wrong ).. 1-Turn on and off the ignition key. 2-Press and release the programmed switch 7 times...and press again and hold it...the led on the 561t brain will flash 7 times.. 3-Press my lock button 3 times ( the led on the brain remain ON ) 4-Press my lock button AGAIN 3 times ( the led on the brain remain OFF ) 5-Press my lock button AGAIN 3 times ( the led flash 2 times - means 3 minutes ) 6-Press my lock button AGAIN 3 times ( the led flash 3 times - means 5 minutes ) 7-Press my lock button AGAIN 3 times ( the led flash 4 times - means 10 minutes ) 8-Release the Program Switch button. Now my Turbo timer set at 10 minutes...Ist the correct way to programming it?
Posted By: Twelvoltz
Date Posted: February 21, 2007 at 7:25 AM
I thought you wanted to turn off the wait to start, not set a turbo timer. These instructions are for menu item number 12, setting the wait to start timer.
You almost have it...but you are on the wrong menu item and are pressing your lock button way too many times. Pressing the luck button ONCE will set it to the next option. In other words:
Ignition on/off
Press and release 12 times, press and hold on the 13th press
Watch the brain LED flash, it will flash 12 times to confirm you are on the correct menu item.
Press lock on the door/remote ONCE the LED will flash 1,2,3 or 4 times if it flashes 1 time your unit is set correctly and the wait to start is off. If it flashes two times the wait to start is set to 15 seconds (as your first post says).
Pressing lock once more will scroll to the next setting, so if your unit is flashing 3 times you will need to press lock twice, once to move it to 4 flashes and once more to move it to 1 flash. I recommend pressing it once, count the flashes, if it is wrong press lock again once more, count the flashes, continue this until you get to the correct number of flashes.
Release the program switch, and you should be done, I always cycle the ignition once more to ensure the unit comes out of programming mode.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: megatfauzi76
Date Posted: February 21, 2007 at 7:59 PM
Thank you so much Twelvoltz... I goin to set again my turbo timer and my wait to start...Really appericiate ur guide.... My last question before i do the setting...If I set off my wait to start ( feautures 12 ) to 1 FLASH...Meaning the wire wait to start ( Grey/Black ) are not connected rite or not use rite?
|