need confirmation, 1700g, 2006 tahoe
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=92325
Printed Date: May 15, 2024 at 11:26 PM
Topic: need confirmation, 1700g, 2006 tahoe
Posted By: auex
Subject: need confirmation, 1700g, 2006 tahoe
Date Posted: March 30, 2007 at 11:07 PM
I need to confirm wether or not keysense needs to be connected for this vehicle. I have been out of the R/S game for a couple years and just want to check. Any other input would be helpful. TIA.
Also the +domelight circuit input.
Thanks all.
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Replies:
Posted By: KarTuneMan
Date Posted: March 31, 2007 at 12:22 AM
I am only going to assume that the 1700G is simular to the GM SL2. I am NOT a DEI type guy. (Even though they bought Astro) Not sure. But at any rate, the keysence is not used on THIS module. For domelight supervision, use the blue/white NEG. behind the headlight switch. -------------
Posted By: auex
Date Posted: April 01, 2007 at 12:31 AM
Thanks, anyone else on the + domelight input on the module?
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: auex
Date Posted: April 02, 2007 at 6:26 PM
Also has anyone had any problems with the module not putting out the signal for the door triggers?
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: Mike M2
Date Posted: April 02, 2007 at 8:45 PM
You connect the + domelight wire to the gray/black on the BCM directly under the steering column. It's in the black plug, pin E. Connect this and your door trigger output will work....
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: KarTuneMan
Date Posted: April 02, 2007 at 9:57 PM
Mike M2...isn't that gray/black @ the bcm (NEG)- ? Teach me...would ya please. How do you take a negative output, and connect it to a + input?
-------------
Posted By: Mike M2
Date Posted: April 03, 2007 at 6:34 AM
KarTuneMan wrote:
Mike M2...isn't that gray/black @ the bcm (NEG)- ? Teach me...would ya please. How do you take a negative output, and connect it to a + input?
It is a positive, not negative. All the dome lights in all the 2003-up GM trucks are positive dome light trigger. . ------------- Mike M2
Tech Manager
CS Dealer Services
Posted By: KarTuneMan
Date Posted: April 03, 2007 at 8:36 AM
Thank you sir......
-------------
Posted By: auex
Date Posted: April 03, 2007 at 11:01 AM
Mike M2 wrote:
You connect the + domelight wire to the gray/black on the BCM directly under the steering column. It's in the black plug, pin E. Connect this and your door trigger output will work....
I did make that connection and the door trigger output worked at first. After the install was completed and the car put together it stopped working. Don't know what happened. ------------- Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: johnmax
Date Posted: April 03, 2007 at 12:09 PM
I think as in with the 457G you have to reset with ignition for it to monitor the door again after a while?
Posted By: f150fan
Date Posted: April 03, 2007 at 9:30 PM
Check to make sure that the dome overide switch is not shut off. If this is shut off the 1700g will not send the signal.
|