wiring compustar 2wss as, '97 240sx

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=92561
Printed Date: April 30, 2024 at 7:06 AM

Topic: wiring compustar 2wss as, '97 240sx

Posted By: nos240
Subject: wiring compustar 2wss as, '97 240sx
Date Posted: April 05, 2007 at 9:34 AM

hey guys, im trying to install a compustar 2wss-as on a 97 240sx with a manual tranny. i was wondering if anyone have any wiring info on it, pretty much the whole installation. i've searched but didn't come up with much. any help is greatly appreciated.

thanks

Replies:

Posted By: Twelvoltz
Date Posted: April 05, 2007 at 9:51 AM

Vehicle Wiring Information:

97 240

-------------
Installer, IT support, and FFL. I need less hobbies.

Posted By: nos240
Date Posted: April 05, 2007 at 10:38 AM

thanks for the reply. i'm also a bit confused on one of the relay. the one with the blue pigtail. i'd imagine it goes to 2nd starter as 2nd ignition and accessory is not available on 240sx. also with the compustar 2wss-as, is it necessary to isolate the accessory wire? this is what i been reading on a couple of posts.

Posted By: dswift
Date Posted: April 05, 2007 at 12:38 PM

hmm it didnt post for some reason.

but yo you have second starter on that car bro

2nd starter BLACK/ green + polarity (ingition harness dude)

-------------
"dont ground out!"

Posted By: nos240
Date Posted: April 05, 2007 at 1:46 PM

thanks dswift, so no 2nd ignition and accessory correct? do you have the rest of the wiring info for the 2wss-as on 240sx by any chance?

thanks

Posted By: nos240
Date Posted: April 09, 2007 at 9:33 PM

got most of the wiring hooke up. got a couple more ?. how do you guys wire up the status output on the compustar. the instruction said connect to transponder or vats module. i don't have any of this. also, i'd like to have the driver priority unlock, how do i go about wiring up the 2nd pulse unlock for the 240sx?

Posted By: mikvot
Date Posted: April 09, 2007 at 10:12 PM

You don't need to hook the status output up to anything. As for the drivers door priority, you are better off leaving it as is.

-------------

Posted By: nos240
Date Posted: April 10, 2007 at 8:25 AM

thanks, but just out of curiousity how would i do it? i searched and found a lot of people wiring in relay(s) to driver's door actuator for drivers priority. i have the factory smart entrance unit on the 240sx, i believe there's built in relays inside the unit and all central lock switching is done internally. how can i make this work?

thanks in advance

Posted By: nos240
Date Posted: April 28, 2007 at 8:00 PM

i been trying to get the turbo timer on the compustar to work. after numerous attempts, it will not work. i have programmed turbo timer to on several times. when i pressed number 3 and 4 button on remote for 1/2 second as per instruction, the turbo timer indicator does not appear on the remote. after setting reservation mode and hand brake, removed key from ignition, get out of car, closed door and car shuts off. no turbo timer. i also disconnected the unit and plugged it back in and try again, still no turbo timer. i have replaced battery and programmed remote as well, no luck.

if all else fails, i do have a greddy turbo timer. does anyone know how to make it work with compustar without triggering the shock sensor as it counting down.

thanks

Posted By: KarTuneMan
Date Posted: April 29, 2007 at 12:04 PM

Try getting the car into reservation mode, and before you open the door, hit the start button on the transmitter.....then get out. See what happens then.

-------------

Posted By: nos240
Date Posted: April 29, 2007 at 6:32 PM

when i set reservation mode and pressed the start button prior opening the door, the car shuts off. i did noticed when i try to activate turbo timer on the transmitter, the remote beep three times and parking lights flashes three times as well. everything else (shock, timer, and passive) beep and flash once when activating. when deactivating, these beep and flashes twice. could this be a fault code in the system? also, now the driver's priority unlock is inoperative. i have programmed this several times as well, but still no worky.

Posted By: dswift
Date Posted: April 30, 2007 at 1:57 PM

you have to program the turbo timer through the option menu.

menu option 1-7

press and HOLD down buttons number 1 & 4 for 3 seconds

the siren will chirp once and the parking lights will flash once.

press number 4 seven times. the siren will chirp everytime you press the number 4 button.

after the seveth time stop. wait until you get the confirmation (the siren will chirp 7 times and wel as your parkinglights will flash 7 times)

press the button number 2 after the seveth flash of the parking lights. and bam your all finished. Engage the e-brake and set the turbo timer.

*remember with turbo timer on the doors will NOT lock by them selves. you have to use the keyless to lock it up.*

-------------
"dont ground out!"

Posted By: nos240
Date Posted: April 30, 2007 at 2:35 PM

thanks for the reply, but i tried that many times already. see page 1. i guess i'll give compustar a call.