92 prelude remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=92911
Printed Date: May 09, 2025 at 10:38 AM
Topic: 92 prelude remote start
Posted By: 4wslude
Subject: 92 prelude remote start
Date Posted: April 13, 2007 at 9:21 PM
Installing remote start on 92 prelude automatic tranny. My car already have a codealarm alarm system on it and I very new at this. So i need some help. Any info would be greatly appreciate thanks. ------------- noob
Replies:
Posted By: pitoaudiovisual
Date Posted: April 13, 2007 at 9:39 PM
do you know anything at all about remote start. do you want to take out the old alarm or just add remote start to the car.
-------------
Confidence is the key to any project!!
Posted By: pitoaudiovisual
Date Posted: April 13, 2007 at 9:40 PM
| Constant 12V+ | White | Ignition Switch Harness | | Starter | BLACK/ White | Ignition Switch Harness | | Ignition | BLACK / YELLOW | Ignition Switch Harness | | Accessory | Yellow | Ignition Switch Harness | | Tach | Blue | Test Connector Passenger's Shock/Strut Tower | | Brake Switch | GREEN / WHITE | Brake Switch | | Trunk Pin | GREEN/ Black (-) | Above Hood Release Gray 14 Pin Connector | | Parking Lights | RED / Black | Light Switch | | Head Lamp | Blue/Red (-) | Switch | | Hood Pin | n/a | | | Factory Disarm | n/a | | | Door Trigger | BLACK/ White (-) | Above Hood Release Gray 14 Pin Connector | | Door Lock | BLACK/ White (-) | Passenger's Kick Panel 10 Pin Connector | | Door Unlock | BLACK/ Red (-) | | | Horn Wire | Blue/Red (-) | Steering Column |
------------- Confidence is the key to any project!!
Posted By: 4wslude
Date Posted: April 14, 2007 at 10:35 PM
I'm adding on a remote start. How do I bypass the impact sensor and the alarm itself ------------- noob
Posted By: enice
Date Posted: April 14, 2007 at 10:46 PM
When remote starting you can interrupt the power wire for the impact sensor. Using a relay it would disconnect the power wire from the sensor. What would activate the relay would be the status output wire for the remote start system. Remember that you should also connect the starter wire of the remote start system to the key side of the starter kill which you problably have installed on your car. If you would like to know the actual wiring of the relay then dont hesitate to ask. By the way your ignition sense wire would actually be disconnected from the ign wire and run together to the remote start system. On DEI remote starts this would be the yellow wire.
Posted By: 4wslude
Date Posted: April 14, 2007 at 11:15 PM
I would like to know the actual wiring of the relay. How many would I need 1 or 2. Thanks
-------------
noob
Posted By: enice
Date Posted: April 14, 2007 at 11:28 PM
just one to intrerrupt the power wire of the sensor. You can also use an additional channel on your remote to activate the remote start system, providing it has additional channels.
Posted By: 4wslude
Date Posted: April 17, 2007 at 10:57 PM
if the power wire of the sensor is interrupted, the alarm is disarm isn't it
-------------
noob
Posted By: enice
Date Posted: April 17, 2007 at 11:29 PM
no, when im talking about the sensor you actually have to look at the harness plugged into the sensor. Usually very small gauge wires that are insulated. One of those wires will have power constantly. that one is the one you interrupt.
|