Im installing an ASIANWOLF FM 2009 in a 2003 nissan xterra. I have a factory alarm installed currently. I Just wanted to know if there where any special instructions for this install? I did find the instructions from this site,
NISSAN / XTERRA / 2003 / Remote Start | | |
| | |
12volts | green | ignition harness |
Starter | BLACK / YELLOW | ignition harness |
Second Starter | GREEN/ YELLOW | ignition harness |
Ignition | BLACK/ white | ignition harness |
Second Ignition | | |
Third Ignition | | |
Accessory | RED / yellow | ignition harness |
Second Accessory | WHITE/ blue | ignition harness |
Notes: NOT required for remote start. | | |
Keysense | | |
Power Lock yellow - SECU | | |
Notes: Meter these wires while turning the key in either door key cylinder. |
| | |
The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
Power Unlock | yellow/red | SECU |
Notes: Meter these wires while turning the key in either door key cylinder. Unlock requires a double pulse. |
| | |
The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
Lock Motor blue | blue 5wi | SECU |
Notes: The SECU (Smart Entrance Control Unit) is to the right of the steering column. | | |
Unlock Motor | GREEN / WHITE 5wi | SECU |
Notes: The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
Parking Lights | blue/red | steering column |
Parking Lights- | | |
Hazards | | |
Turn Signal(L) | | |
Turn Signal(R) | | |
Reverse Light | | |
Door Trigger - | | |
Vehicles with power door locks use GREEN/ red for the driver door, GREEN/ black for the front passenger door, and RED / black for the rear doors. All found at the SECU, use all three wires and diode isolate each. |
|
The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
Dome Supervision | | |
Trunk/Hatch Pin | | |
Hood Pin | BLACK/ pink | SECU |
Notes: The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
Trunk/Hatch Release | | |
Power Sliding Door N/A | | |
Factory Alarm Arm arms with lock | | |
Factory Alarm Disarm disarms with unlock | | |
Disarm No Unlock single pulse on unlock wire | | |
Tachometer | pink/blue or black | instrument cluster or ECM |
Notes: The ECM (Engine Control Module) is located below the heater box to the right of the accelerator pedal, behind trim panel. The tach is in the top row, 3rd pin left of center of the plug. |
Wait to start N/A | | |
Brake Wire | BROWN / red | brake pedal switch |
Parking Brake | | |
Horn Trigger lt | GREEN/ red or brown | steering column |
Im doing this install on monday and wanted to get everything ready and setup before hand. Thanks for the help
Nope, nothing special if its just an alarm..............slaaaammmerrrrr
NISSAN, XTERRA, 2003, Door Trigger On vehicles without power door locks use RED / black at any door pin switch or also found in the driver A pillar. Vehicles with power door locks use GREEN/ red for the driver door, GREEN/ black for the front passenger door, and RED / black for the rear doors. All found at the SECU, use all three wires and diode isolate each.
The SECU (Smart Entrance Control Unit) is to the right of the steering column. |
-------------
Thank alot for those directions. Im a little rusty. Im having problems with the door locks. Could someone show me a diagram that would work for my application. I believe i have a 2 zone reversed polarity. But i could be wrong. Am i going to need relays? I have a couple i believe to be 5wi modules. Could i use those? I have almost the rest done. Just need to figure out window modules. I will post about that later. Thanks. I have pictures of instructions for my alarm if needed.