1999 honda accord factory alarm
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=94337
Printed Date: June 19, 2025 at 4:05 PM
Topic: 1999 honda accord factory alarm
Posted By: stereoguyz
Subject: 1999 honda accord factory alarm
Date Posted: May 29, 2007 at 12:23 PM
Installed an add-on remote start to a 99 accord and everything works perfect except for the remotes do not operate after the car is running, this causes a problem when trying to get into the vehicle. I have programed the remote start activation to enable on lock 3 pulses, but after running into this problem i changed it to unlock 3 times. Anyone got info on factory alarm ignition wire, or how to enable the remotes to work again after starting? Thanks in advance.
Replies:
Posted By: dswift
Date Posted: May 29, 2007 at 1:24 PM
what type of remote start did you install? And why would you need triple pulse for on a accord? hmm. need to know more info homie. So your saying after remote starting the vehicle your R/F doesnt respond? Is that correct?
-------------
"dont ground out!"
Posted By: mobilecustoms
Date Posted: May 29, 2007 at 1:52 PM
honda factory remotes do not work when the car is running. You need to use the key in the door.
-------------
Posted By: peterubers
Date Posted: May 29, 2007 at 1:58 PM
get r/s brain w/ keyless entry -- new keyfobs will work the way you want.
-------------
The search function is your friend.
Posted By: stereoguyz
Date Posted: May 29, 2007 at 4:42 PM
Used a generic remote starter and it requires a triple pulse or a single pulse to start, when using an aftermarket alarm a single pulse is fine, but when using a factory keyless triple is better to insure starting when actually wanted. My question is how do i get the factory keyless to think the ignition is off when remote started then allowing the keyless entry to still operate.
Posted By: stereoguyz
Date Posted: May 29, 2007 at 4:49 PM
need wiring schematic to factory keyless modual (ignition wire) to re-enable keyless entry
Posted By: stereoguyz
Date Posted: May 29, 2007 at 5:05 PM
Ok figured it out myself. Just for anyone outthere with picky customers who want remote start and dont want to change their remote this is what u have to do. Find the multi plex unit (fuse box drivers side) DMM test for a blue wire with a white trace rests at 12v with ign off, ign on goes to ground. Cut blue wire with white trace, add in a constant 12v fused with a 10 amp fuse - problem solved. :) Thanks for all the speedy responses and help though guys!
Posted By: capted100
Date Posted: May 29, 2007 at 10:39 PM
i have a problem on my steel mate auto security system because the wiring diagram is not very spicific ( martian model # 6005 ) . the 6 wire harmnes only instruct me to connect to central locking and i dont know where to coonect those wire. My car is a 1994 Honda accord. Can i ask a detailed wiring diagram for my steel mate auto security system and instructions on how to connect the wire ? Thanks in advance and more power, god bless.............
Posted By: KarTuneMan
Date Posted: May 30, 2007 at 8:40 AM
6 wire harness for the door locks? If so, this unit has built in door lock relays. The wires should be labeled, N.C. (normaly closed) N.O. (normally open) and common. The represent pins on a standard relay. in this order 87a, 87, and 30.
-------------
|