2001 ford mustang window module

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=94969
Printed Date: May 05, 2025 at 1:01 AM

Topic: 2001 ford mustang window module

Posted By: chrismiddleton
Subject: 2001 ford mustang window module
Date Posted: June 20, 2007 at 9:25 PM

I have a 2001 Ford Mustang Gt that I hooked up a pyle alarm up to. I bought a "Smart" Window module. It is supposed to roll both windows up and down. I am wanting to know how I should wire this thing up. Will I need any diodes or relays or anything like that?

BLACK/ white-(Cut loop for 2 window up/down mode)

GREEN/ Black=Front right motor down

Green= Front right switch down

Red= Fused 12v constant

Blue/black= front left motor down

blue=front left switch down

black=ground

BROWN / blue= front right motor up

brown= front right switch up

yellow= (-) up activation input

yellow/white=(-) down activation input

WHITE/ blue= front left motor up

white=front left switch up

If anyone has installed these in a mustang can you please let me know what I should need to install this.

Thanks,

Chris

Replies:

Posted By: chrismiddleton
Date Posted: June 20, 2007 at 9:29 PM

I got the wiring im just looking for added info.

------------------------------
RADIO_MEMORY   GRN/YEL
RADIO_SWITCHED   YEL/BLK
RADIO_GROUND   BLK/GRN -
RADIO_ILLUMINATION   LT.BLU/RED
FRONT_SPEAKER_SIZE   5 X 7'
FRONT_SPEAKER_LOCATION   FRONT DOORS
FRONT_RIGHT_SPEAKER_POSITIVE   WHT/LT.GRN
FRONT_RIGHT_SPEAKER_NEGATIVE   NA
FRONT_LEFT_SPEAKER_POSITIVE   ORG/LT.GRN
FRONT_LEFT_SPEAKER_NEGATIVE   LT.BLU/WHT
REAR_SPEAKER_SIZE   5 X 7'
RIGHT_REAR_SPEAKER_POSITIVE   ORG/RED
RIGHT_REAR_SPEAKER_NEGATIVE   BRN/PNK
REAR_LEFT_SPEAKER_POSITIVE   GRY/LT.BLU
REAR_LEFT_SPEAKER_NEGATIVE   TAN/YEL
POWER_ANTENNA_TRIGGER   AMP=BLU
-----------------------------------------------------
Security Information

STARTER   WHT/PNK +
START_LOCATION   IGNITION SWITCH HARNESS
TACH_WIRE   LT.GRN/WHT
TACH_LOCATION   POWER CONTROL MOD BEHIND RT.KICK
IGNITION_WIRE   RED / LT.GRN
IGNITION_LOCATION   IGNITION SWITCH HARNESS
IGN_2_WIRE   GRY/YEL +
IGN_2_LOCATION   IGNITION SWITCH HARNESS
ACCESSORY_WIRE   GRY/YEL +
ACCESSORY_LOCATION   IGNITION SWITCH HARNESS
NEUTRAL_SAFE_WIRE   WHT/PNK
NEUTRAL_SAFE_LOCATION   IGNITION HARNESS
BRAKE_SW   RED / GRN (+)
BRAKE_LOCATION   AT BRAKE SWITCH
SPEED_SENSE   WHT/ORG
SPEED_LOCATION   PIN 68 AT PCM RT. KICK PANEL
WINDOW_UP   LF:WHT/BLK
WINDOW_UP_LOCATION   RF:WHT/YEL LR:GRY/ORG RR:RED / BL
WINDOW_DOWN   LF:YEL
WINDOW_DOWN_LOCATION   RF:TAN/LT.BLU LR:YEL/BLU RR:YEL/BL
TRUNK_WIRE   VIO/YEL (+)
TRUNK_LOCATION   AT SWITCH OR DRIV KICK PANEL
HEADLIGHTS   YEL/RED (+)
HEAD_LOCATION   AT LIGHT SWITCH
FACTORY_ALARM   DK.GRN/VIO(-)
FACTORY_LOCATION   KEYLESS MODULE
TRUNK_SWITCH_WIRE

Posted By: chrismiddleton
Date Posted: June 30, 2007 at 7:13 AM

Well I havent got this module to work right. The only window I have gotten to go down is the passanger side and it was accedentally left unplugged. Both sides wont go up and both wont go down with the switches plugged in. The module is also getting warm and making a humming noise which cant be a good sign. Could I please have some help. I have all the wires that are supposed to be ran to the motors like 2 inches from both motors and the same goes for the switches also.

Here is how I have it wired

Window module Car window wires

Pass side motor down- GREEN/ black to the Red wire on motor

Pass side motor up- BROWN / Blue to Yellow wire on motor

Pass side switch up- Brown to WHITE/ Yellow

Pass side switch down- Green to Tan/Light blue

Drivers motor down- Blue/Black to Yellow on motor

Drivers motor up- WHITE/ blue to Red on motor

Drivers switch down- Blue to Yellow

Drivers switch up- White to WHITE/ black

Then of corse the 12v power, ground, and I cut the loop.

Can someone please help me out? posted_image

Posted By: chrismiddleton
Date Posted: July 01, 2007 at 3:20 AM

I guess nobody on here knows

Posted By: fox55
Date Posted: July 07, 2007 at 1:22 PM

Sorry that nobody is helping you, but I just did the same window module on a 2000 Mustang a week ago and its the same, so here it goes:

First of all you must have the wrong wires for your drivers window because they are both WHITE/ black. These two wires are below where the main harness in the door splits to the switch. The two WHITE/ black wires go in to a white connector and come out red on other side. You will need to meter these two wires to find which is up and which is down since they are same color. After you figure out which is which this is how it goes. Remember plug side is motor side. Cut wires

Driver up WHITE/ black switch side - white

Driver up WHITE/ black plug & motor side - WHITE/ blue

Driver down WHITE/ black switch side - blue

Driver down WHITE/ black plug & motor side - blue/black

I don't know where you are getting these red and yellow wires from, but they have nothing to do with anything you have to worry about

As far as the pass side you are half right on that one. Don't know where you are tagging your pass side wires, I did it in the drivers kick. but this is how pass goes:

Pass up tan/lt blue switch side - brown

Pass up tan/lt blue motor side - BROWN / blue

Pass down WHITE/ yellow switch side - green

Pass down WHITE/ yellow motor side - GREEN/ black

This is how I did it and works perfectly

Hope this helps out posted_image

Can't believe that over 100 people have looked at this and could not help posted_image

-------------
MECP Certified
Fry's Electronics MEI - Anaheim, Ca

"Kneel Before Zod"