honda crv 2005 factory keyless disable
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=98242
Printed Date: May 13, 2025 at 8:18 AM
Topic: honda crv 2005 factory keyless disable
Posted By: a24036
Subject: honda crv 2005 factory keyless disable
Date Posted: October 23, 2007 at 9:22 AM
Good day Is there a way to unable keyless entry when engine is running? I install RS1100 by Bulldogsecurity. They give an option to use factory keyless remote to operate Remote Starter. Now I can start the car but since keyless does not work while engine is running I can not operate Remote Starter with factory keyless remote and I can not open the door either.:-)(well, I can use a key, but that would not be a good sport). Any solutions? Thank you
Replies:
Posted By: Velocity Motors
Date Posted: October 23, 2007 at 10:09 AM
You need to use a system that doesn't use the OEM key FOB
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Twelvoltz
Date Posted: October 23, 2007 at 10:36 AM
If your RS1100 is the one listed on bulldogsecurity.com then it has the outputs you need to use the new system to lock and unlock the doors. The 05 CR-V uses type B (negative pulse) door locks. Lock is WHITE/ blue unlock is WHITE/ green in the driver's kick panel harness that goes into the door.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: a24036
Date Posted: October 23, 2007 at 1:48 PM
to Velocity Motors I guesse I missed my status(rookie) :-)) OEM - original equipement manufacter? What it FOB? to Twelvoltz: If I understand correctly your advice will help to open and close the doors with bulldog's remote.(I'm not sure it's possible at all since remote has only 2 buttons:start and stop) I'm trying to make factory keyless remote manage Remote Starter. according to bulldog I can programm the Remote Starter Unit to start if I press Lock button on factory keyless remote 3 times and stop when I press Lock button another 3 times. So start operation works but then car ignores factory keyless remote since engine is running.
Posted By: a24036
Date Posted: October 23, 2007 at 2:04 PM
And thank you for the help.
Posted By: Twelvoltz
Date Posted: October 23, 2007 at 2:35 PM
I went to bulldog's site and they listed a RS1100xxxx. That unit had door lock outputs if yours does not then your only real option (as Velocity has stated) is to get a different unit that provides those outputs.
On your vehicle the keyless entry is a function of the BCM. By design it will not work when the vehicle is running. You can not use the factory remotes to lock/unlock once started. The only way to shut it off once running is to step on the brake, or press lock on the door panel three times. 
FOB------------- Installer, IT support, and FFL. I need less hobbies.
Posted By: a24036
Date Posted: October 23, 2007 at 3:29 PM
My bad. It's not RS1100. It is RS82P. RS1100 has door lock harmess but RS82P doesn't. Thank you for the help. BTW, in case it can help anyone: Factory alarm plug on my car was not just hanging but was attached with sort of tape in up position with wire bundle. It took me a while to find me. And I used GREEN/ black wire wich becomes negative when you press lock button of factory remote. I used that wire to feed negative(blue) input on my Remote Starter which allowed to skip relay. My Remote Starter has negative FASD output. I notice on forum that there is FASD input wire in door harness to shutdown alarm when you open door with the key. Do you think I can use this wire to shutdown alarm and feed driver's door unlock wire?
Posted By: a24036
Date Posted: October 23, 2007 at 3:49 PM
Another "fiture" of my instalation: when I was locking the car using Lock button of remote, Hoda use to flush parking light. If I press Lock button again it was flushing the lights and giving signal. Now it just quitely locking the car giving no confirmation. What do you think I broke?
|