Print Page | Close Window

01 caravan alarm problem

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=98246
Printed Date: October 31, 2024 at 6:44 PM


Topic: 01 caravan alarm problem

Posted By: desh187
Subject: 01 caravan alarm problem
Date Posted: October 23, 2007 at 12:01 PM

Installed a 2 way compustar (cm3000 module)on a 2001 Dodge Caravan.Everything works fine except when i did the individual door triggers using 1amp diodes,after alarm is armed,it triggers after about a minute.The 2 way pager shows a door is open.
I have used the + trigger for now(yellow/orange)which is fine but when i arm,the pager beeps 4 times showing door open.
What can i do to resolve this?
Is there a way to delay the door trigger on the alarm module(i did not see one in the install manual)as that would take care of the problem.
Any feed back will be very much appreciated.Thanks.



Replies:

Posted By: techman93
Date Posted: October 23, 2007 at 4:46 PM
12volts lt. blue/red (10A)   +   ignition harness
Notes: This wire is rated at 10 amps only. If installing any system with high current outputs, go to battery for 12v.


Starter yellow   +   ignition harness
Second Starter PURPLE / brown   -   ignition harness
Notes: The second starter wire is negative trigger thru a 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1083 for wiring information.
Ignition pink/white   +   ignition harness
Second Ignition N/A       
Third Ignition N/A       
Accessory not required for remote start       
Second Accessory N/A       
Keysense          
Power Lock PURPLE / green   -   conn. 3, pin 21 @ BCM
Notes: Lock is negative trigger thru a 5.3K ohm resistor. Unlock is negative trigger thru a 2.0K ohm resistor. MUST use relays.

The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.

Can also use Directed 457C or 456L interface modules.
Power Unlock same wire as power lock       
Lock Motor tan/white      conn. 2, pin 10 @ BCM
Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Unlock Motor tan/lt. green      conn. 2, pin 28 @ BCM
Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Parking Lights+ DO NOT USE       
Parking Lights- WHITE/ brown   -   headlight switch
Notes: The parking lights are negative trigger thru a 2.1K ohm resistor. The headlights are negative trigger thru a 790 ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch. See DirectFax document 1082 for wiring information.
Hazards          
Turn Signal(L)          
Turn Signal(R)          
Reverse Light          
Door Trigger     -   conn. 3 @ BCM
Notes: There are separate door triggers for each door, they are all in connector 3 at the BCM. The driver door trigger is purple in pin 6, the passenger door is PURPLE / white in pin 7, the left sliding door is PURPLE / gray in pin 8, and the right sliding door is purple / YELLOW in pin 5. Use all four and diode isolate each. See DirectFax document 1076 for wiring information.

The BCM is in the drivers kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Dome Supervision use door trigger       
Trunk/Hatch Pin PURPLE / orange   -   conn. 3, pin 29 @ BCM
Notes: A diode must be placed inline on this wire to avoid problems with the dome lights and parking lights.

The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Hood Pin PURPLE / lt. blue   -   conn. 3, pin 30 @ BCM
Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Trunk/Hatch Release PURPLE / tan   -   conn. 2, pin 6 @ BCM
Notes: Hatch release is negative trigger thru a 1.69K ohm resistor. MUST use a relay.

The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Power Sliding Door PURPLE / blue   -   conn. 3, pin 1 @ BCM
Notes: Left power sliding door is negative trigger thru a 1.5K ohm resistor. Right power sliding door is negative trigger thru a 2.7K ohm resistor. MUST use relays.

The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.
Factory Alarm Arm PURPLE / lt. blue   -   conn. 3, pin 14 @ BCM
Notes: Arm is negative trigger thru a 1.5K ohm resistor, this will also lock the doors. Disarm is negative trigger thru a 9.1K ohm resistor, if use double pulse this will also unlock the doors. MUST use relays.

The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.

Can also use Directed 457C or 456L interface modules.
Factory Alarm Disarm same wire as alarm arm       
Disarm No Unlock          
Tachometer     ac   ignition coil pack
Notes: On the 2.4L use blue/green or blue/tan. On the 3.3L/3.8L use blue/green, blue/tan or blue/orange.
Wait to start          
Brake Wire WHITE/ tan   +   brake pedal switch
Parking Brake          
Horn Trigger GREEN/ purple   -   steering column
Memory Seat 1          
Memory Seat 2          
Memory Seat 3          
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Sentry Key
Part #: 555CW
Alternate Part1 #: 556UW
Alternate Part2 #: 555U
Notes: Only vehicles with gray keys have the immobilizer.
Interface Module: Category:
Door Lock Interface Required:
Yes Type:
Data Bus
Part #: 457CW
Alternate Part1 #: 456LW
Notes:

***** The output to the domelight is unreliable and can cause false triggering with some after-market alarm systems. For proper monitoring, it is best to use the separate doorpin wires. They are all found at the middle connector on the BCM under the driver's side dash on the firewall. VIOLET - driver's door, VIOLET/WHITE - passenger door, VIOLET/GRAY - left sliding door, VIOLET / YELLOW - right sliding door. For exact pin locations, see the BCM graphic for this vehicle.




Posted By: kola7126
Date Posted: October 24, 2007 at 5:03 PM
It is necessary to put diodes in break of wires from triggers of each door (4 diodes) and the trigger of a luggage carrier. It except for earlier connected diodes.





Print Page | Close Window