problems command start, 92 wrangler

Hey Guy maybe you can help me.

I am trying to install a command start PRO START CT-3260 on Jeep Wrangler 1992. It is a manual transmission, no power door/locks/windows/dome light.

I wired up everything except for green wire on the 6 pin plug. The green wire says - ((+) 5th Relay output (30 A) This high-current output can be used to power a second Ignition, Accessories or Crank wire.)

On the 5 pin plug I have everything wired up as per https://www.the12volt.com/installbay/alarmdetail/1233.html . I have Purple wire for the tach input going to the coil and hooked up to Yellow/Black again as per instructions.

Then I have 12 Pin Harness - on that one i have only parking brake wire installed. Not sure if there is anything else to be hooked up on that harness

Basically i can program the remote and i get feedback from it, I also I can go Into a Ready mode, I can start the car with the key, then pull the key out and it will stay running, then when i press 2nd button, engine will shut off. But i cannot start the car with the remote. What did I miss? I do not think car has any security to bypass, and the car starts without pressing clutch. There are #9 and #10 wires on 12 pin harness and I am not sure if they have to be connected, and where should they be connected.

Please Help.

Thanks

Dan

I believe you need a door pin input to the R/S.

If it were an astrostart you were installing....I would know for sure this is the problem.

A Compustar guy will chime in here Im sure.

hey guys, i thought i posted this but maybe i forgot to, but here are instructions to the pro start CT-3260

https://www.engines911.com/asdocs/CT-3260_ig_en_h370s380v155_040922.pdf

Thanks.

here's the thing

there is no door pin on the vehicle at all.

also right now as it stands I am bypassing my parking brake wire, I just ground it out to bypass. I cannot locate the wire for the brake. I just didn't see that wire, any idea where i should hook it up? the cheat sheet says its black with yellow line. But i did not see any black wires with yellow lines. I've seen some yellow with black line, and I tested it, but it wasn't it.

thanks

You gotta find a way to add one. Theres got to be some free space for a 90 degree hood pin. L shaped. Something on the body the goes to ground when the door is opened, and open when the door is open. Youll want to isolate this one stinckin wire with a diode to prevt any current from traveling to the door pin from the R/S.

what should i do about the parking brake wire?

I have one single wire comming off parking brake switch. When i had R/S connected to that wire it didn't give any feedback to R/S.  Then i disconnected R/S Parking brake wire from the brake switch and just grounded it out, after that i did get feedback to R/S. So is there another wire somewhere in Parking brake circuit that i should find?

As for the Door Pin, I think i should go and buy one, or can i just bypass that one to the ground also?

thanks

Dan

hey guys a little update.

I am still 110% lost and need some help. I've installed a door switch. It works, and also turns on the door lights. I hooked up negative side of the R/S door wire to it.

I am still not having any luck with parking brake. I've connected to the parking brake wire that is shown in the Wrangler diagram and still nothing.

Basically the same story, I can put the vehicle into ready mode when i ground out parking brake wire from R/S. then I push II button and it shuts down, but won't start back up.

This vehicle starts without pushing in clutch. Should I still bypass clutch?

hey guys here's a schematic of parking brake switch. as you see its case grounded, so how would i connect R/S parking brake wire to a negative side of the switch?