2007 explorer 1100f
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=99475
Printed Date: May 04, 2024 at 12:43 AM
Topic: 2007 explorer 1100f
Posted By: joey2714
Subject: 2007 explorer 1100f
Date Posted: November 29, 2007 at 10:31 AM
I got my entire alarm working, the viper 5900. But im having problems with the 1100F bypass. Someone please tell me which wires and how to hook it up and program it. Thanks guys!
-------------
Pioneer Avic D3
Rockford Fosgate T15004
Rockford Fosgate T20001BD x 2
15" Fully Loaded Fi BTL x 2
6" Eminence Alpha Mids x 16
Eminence APT-80 Tweeters x 16
260 Amp Iraggi alt
Kinetik 2400 x 3
Replies:
Posted By: Twelvoltz
Date Posted: November 29, 2007 at 12:26 PM
The instructions for the 1100F lay it out pretty well. What is your exact question?
You need to provide the 1100F with ground, constant hot, ignition input, and ground when running from the RS. Then the RX and TX wires get wired into the vehicle. Looking at the pictures shown in the manual you should be able to identify which wires are which. If you get the TX and RX backwards no harm is done, and reversing them will fix the issue. But if you pay attention to where the ground and ignition wires are in that harness you should not have any problem finding the TX and RX.
Ignoring the actual pin numbers: If the plug is layed out with ground on the first pin from the end and the next wire is ignition the third wire will be RX, if it is ignition on the first pin and ground in the second the third wire will be TX.
Once your connections are made, make sure you are in installation mode 2 and program the box like you were adding a third key to the vehicle. Key 1 in until red light on dash goes out, key 2 in until red light goes out, remote start the vehicle.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: joey2714
Date Posted: November 29, 2007 at 6:36 PM
ok im gonna go try again.. i thought i did all that but maybe tx and rx are backward. ill go try thanks ill be back soon with results
-------------
Pioneer Avic D3
Rockford Fosgate T15004
Rockford Fosgate T20001BD x 2
15" Fully Loaded Fi BTL x 2
6" Eminence Alpha Mids x 16
Eminence APT-80 Tweeters x 16
260 Amp Iraggi alt
Kinetik 2400 x 3
Posted By: moonliter
Date Posted: November 29, 2007 at 11:50 PM
Here is the pin configuration for 2007 ford explorer. 
Posted By: joey2714
Date Posted: November 30, 2007 at 11:12 AM
thanks bro.. and my domelight slowly fades out when the doors are locked, which causes the alarm to bypass the doors i believe, how can i change that? And any wiring diagram for my windows by any chance so i can hook up the 530T? Thanks
-------------
Pioneer Avic D3
Rockford Fosgate T15004
Rockford Fosgate T20001BD x 2
15" Fully Loaded Fi BTL x 2
6" Eminence Alpha Mids x 16
Eminence APT-80 Tweeters x 16
260 Amp Iraggi alt
Kinetik 2400 x 3
Posted By: tedmond
Date Posted: November 30, 2007 at 2:12 PM
i think viper units do have dome light delay, it doesnt bypass or fully arm untill 30 seconds (usually length until light goes out)
|