2012 toyota sienna data imo , imi?
Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=131405
Printed Date: May 12, 2025 at 11:56 PM
Topic: 2012 toyota sienna data imo , imi?
Posted By: giddyup4821
Subject: 2012 toyota sienna data imo , imi?
Date Posted: May 14, 2012 at 2:33 PM
I just wired up a viper car starter and am stuck on finding the data IMO and data IMI wires. Ive read to the left of the steering column it is the green and purple but cannot find them there. Does anybody know where these wires are? I have a LE AWD V6 without the smart key and I'm wiring in an express kit XK05. Thanks
Replies:
Posted By: kreg357
Date Posted: May 14, 2012 at 4:48 PM
This should help : https://www.checkyourground.com/------------- Soldering is fun!
Posted By: giddyup4821
Date Posted: May 14, 2012 at 8:07 PM
Can't get a better view then that! Thank you!!
Posted By: kreg357
Date Posted: May 14, 2012 at 8:25 PM
A picture is worth a thousand words...  ------------- Soldering is fun!
Posted By: giddyup4821
Date Posted: May 15, 2012 at 3:07 PM
Just wired it up this morning. Very easy to find those wires after seeing that websites picture. Thanks again kreg357!!
Posted By: blazing_nitro
Date Posted: November 27, 2012 at 7:41 PM
Can you send me link to the wiring diagram thanks
Posted By: kreg357
Date Posted: November 27, 2012 at 7:44 PM
Here is a link to the wiring info from ReadyRemopte : https://www.readyremote.com/main.asp?make=Toyota&model=Sienna------------- Soldering is fun!
Posted By: blazing_nitro
Date Posted: December 15, 2012 at 6:46 AM
I started installing my compustar in my sienna. For the accessory wire I found the blue wiring at the ignition connector but it is on PIN number 2. The instructions indicate that the blue wire should be PIN number 3 which is white. Anybody have some suggestions. How can I test this I don't want to fry anything.
Posted By: howie ll
Date Posted: December 15, 2012 at 9:29 AM
Use a DMM.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: blazing_nitro
Date Posted: December 15, 2012 at 7:44 PM
I do have a voltage meter. Do you know what I should be looking for if it will be 0v without key, 12v in accessory, 0v when starting, and 12v when ignition in the on position. I would also be interested in knowing what the other wires are in the ignition switch are as there is a total of six wires and I'm using or wiring just three. Wish I had the dealer wiring diagram so I could be totally sure. I'm still beginner but trying. Anybody know what would happen if I don't wire the accessory? I'm hoping its not needed but want to make sure I have heat going through accessory blower.
Posted By: kreg357
Date Posted: December 15, 2012 at 10:21 PM
Here is a link to an early Viper Install Guide that has a pretty good section on using a DMM to locate and verify the common vehicle wires used for a remote start install : https://www.the12volt.com/installbay/file.asp?ID=618 The info starts on Page 9. ------------- Soldering is fun!
|