2012 Toyota 4Runner Remote Start Wiring
Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=133004
Printed Date: May 08, 2025 at 5:51 AM
Topic: 2012 Toyota 4Runner Remote Start Wiring
Posted By: chiarlanza
Subject: 2012 Toyota 4Runner Remote Start Wiring
Date Posted: December 17, 2012 at 11:06 PM
Looking for 2012 Toyota 4Runner remote start wiring.
Replies:
Posted By: shortcircuit161
Date Posted: December 18, 2012 at 8:09 AM
DIRECTWIRE™ WIRING INFORMATION - TOYOTA / 4RUNNER / 2012 / Remote Start
[PRINT THIS PAGE]
12volts green (30A) + ignition switch, white 8 pin plug, pin 7
Notes: If equipped, the Satellite Radio Tuner is under the front passenger seat.
Starter red + ignition switch, white 8 pin plug, pin 8
Second Starter black + ignition switch, white 8 pin plug, pin 1
Ignition black + ignition switch, white 8 pin plug, pin 6
Second Ignition purple + ignition switch, white 8 pin plug, pin 4
Third Ignition N/A
Accessory red + ignition switch, white 8 pin plug, pin 3
Second Accessory N/A
Keysense black - Body ECU, white 30 pin plug, pin 17
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
Power Lock black (passenger door switch) - Body ECU, white 30 pin plug, pin 9
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
This wire is only needed if the door locks do not function with the aftermarket system while the vehicle is running. All other times just use the factory alarm arm wire.
Power Unlock white (passenger door switch) - Body ECU, white 30 pin plug, pin 10
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
This wire is only needed if the door locks do not function with the aftermarket system while the vehicle is running. All other times just use the factory alarm disarm wire.
Lock Motor blue 5 wire dash fuse box, white 36 pin plug (2F), pin 8
Unlock Motor white 5 wire driver kick, white 20 pin plug, pin 1
Parking Lights+ green + dash fuse box, white 36 pin plug (2F), pin 16
Parking Lights- red - Body ECU, white 30 pin plug, pin 30
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
Hazards white - Body ECU, white 30 pin plug, pin 3
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
Turn Signal(L) yellow (F), yellow (R) + turn signal flasher right of dash FB, white 18 pin plug, pins 10 and 2
Turn Signal(R) lt. blue (F), lt. blue (R) + turn signal flasher right of dash FB, white 18 pin plug, pins 17 and 8
Reverse Light red + dash fuse box, white 36 pin plug (2F), pin 4
Door Trigger red - dash fuse box, white 36 pin plug (2F), pin 27
Dome Supervision green - dash fuse box, rear, white 40 pin plug (2B), pin 18
Trunk/Hatch Pin pink - Back Door ECU in liftgate, white 26 pin plug, pin 10
Hood Pin black - dash fuse box, white 40 pin plug (2D), pin 23
Trunk/Hatch Release use trunk release motor
Power Sliding Door N/A
Factory Alarm Arm lt. green (driver door key lock) - Body ECU, white 30 pin plug, pin 11
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
Factory Alarm Disarm gray (driver door key unlock) double - Body ECU, white 30 pin plug, pin 24
Notes: The Body ECU is under the driver dash, attached to the right side of the dash fuse box.
Disarm No Unlock use keysense
Tachometer pink ac data link connector, white 16 pin plug, pin 9
Wait to start N/A
Brake Wire PURPLE / green to blue + brake switch or dash fuse box, white 36 pin plug (2F), pin 29
Parking Brake lt. green - dash fuse box, white 40 pin plug (2D), pin 17
Horn Trigger gray to gray/blue - horn switch or dash fuse box, white 40 pin plug (2D), pin 29
Memory Seat 1 N/A
Memory Seat 2 N/A
Memory Seat 3 N/A
Interface Modules: Not Available
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
-------------
|