viper 5701 on 2012 patriot

Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=135568
Printed Date: May 06, 2024 at 8:34 PM

Topic: viper 5701 on 2012 patriot

Posted By: danieljames
Subject: viper 5701 on 2012 patriot
Date Posted: December 18, 2013 at 10:22 PM

Just want to make sure I got this right
Alarm.Car
H3/1
Pink/ignition 1-pink/white at ISH
H3/2
RED / white fused ignition2 flex relay- not used
H3/3
Orange +accessory output-not used
H3/4
Violet +starter output (car side)-yellow/gray ISH
H3/5
Green+starter input (key side)-yellow/gray ISH
H3/6
Red+ fused ignition1 input-pink/white ISH
H3/7
Pink/white +ignition2-not used
H3/8
Pink/black +flex relay input 87a key side of flex nu
H3/9
RED / black +fused accessory starter input-battery?
H2/10
Dark blue (-)200mA status output-bypass module
H2/11
Pink/white(-)200mA flex relay control output-nu
H2/12
Orange(-)200mAaccessoryoutput-pin85asTD1084
H2/13
Purple(-)200mAstarter output-pin85 asTD1084
H2/14
Pink(-)200mA ignition 1 output-not used
H2/15
Grey(-)hood pin input-hood pin switch
H2/16
Blue/white(-)200mA 2nd status/reardefog-nu
H2/17
Brown(+)brake shutdown-darkGREEN / WHITEBP
Any input would be great starting project in the morning done lot of research just want to know I'm getting it right

-------------
DJDoo

Replies:

Posted By: danieljames
Date Posted: December 18, 2013 at 10:33 PM

Ok fix the H3/4 anH3/5 will go under hood guess cut yellow/grey there and H3/4 on module side H3/5 on other side would that be right

-------------
DJDoo

Posted By: danieljames
Date Posted: December 20, 2013 at 8:09 PM

Ok so I did the smart thing and bought the dball interface made the install much easier except I failed to realize that the interface had to be programmed with the xkloader2 so after calling every installer around and getting denied for them to load the firmware finally I found one installer that had no problem doing it for me so Sunday I am meeting him. Is there anything else I need to know is just taking the dball interface to him ok or should I take the vehicle. I install the dball interface. Hooked everything up as shown in the dball diagram type 3c was this right and do I hook the 4 pin plug from the dball interface to the remote start after the firmware is installed on it

-------------
DJDoo

Posted By: kreg357
Date Posted: December 21, 2013 at 6:46 AM

Have the shop flash the 401.Chrysler v5.06 firmware on to the DB-ALL. Follow the Type 3C install diagram. The Pictorial
will show you the Parking Light wire, a good +12V constant source, a chassis ground location and the ignition switch
connector wires. The only wire not shown is the Driver Door pin for RAP shutdown.

There will be additional wires needed from the Viper such as :
H1/2 Red +12V
H1/3 Brown Siren
H3/6 Red +12V
H3/9 RED / Black +12V

Install the Vipers Neutral Safety Switch and set to ON.

After the DB-ALL is flashed with the firmware, follow the install guide for proper order of connecting the harnesses and then the steps for programming the bypass module to the Jeep. There is a specific section for vehicles without factory remote keyless entry.

-------------
Soldering is fun!

Posted By: danieljames
Date Posted: December 21, 2013 at 9:14 AM

That you so much for all your help couldn't have done it without you I will post back an let you know how it goes.

-------------
DJDoo