Wiring for Honda HRV/HR-V/Vezel 2015/16

Hi all,

Does anybody have the wiring diagram for the Honda HRV/Vezel 2015/2016?

I'm trying to install the scuff plates/door sill illumination. I need to locate the Dome lighting wiring at each door and tap on both the +12 and the ground.

better still if somebody has a diagram or info for all other wiring. I'm sure it will come in very handy in the near future.

Thanks in advance!

2016 Honda HRV Alarm Wiring Diagram

Battery Constant 12v+ Positive Wire (+): White
Battery Constant 12v+ Positive Wire Location: At Ignition Switch Harness (White 5-Pin Plug)
Starter Positive Wire (+): Green
Starter Positive Wire Location: At Ignition Switch Harness (White 5-Pin Plug)
Second Starter Positive Wire (+): N/A
Second Starter Positive Wire Location: N/A
Ignition Positive Wire (+): Red
Ignition Positive Wire Location: At Ignition Switch Harness (White 5-Pin Plug)
Second Ignition Positive Wire (+): N/A
Second Ignition Positive Wire Location: N/A
Third Ignition Positive Wire (+): N/A
Third Ignition Positive Wire Location: N/A
Accessory Positive Wire (+): Purple
Accessory Positive Wire Location: At Ignition Switch Harness (White 5-Pin Plug)
Second Accessory Positive Wire (+): Yellow
Second Accessory Positive Wire Location: At Ignition Switch Harness (White 5-Pin Plug)
Key Sense Wire: N/A
Key Sense Wire Location: N/A
Parking Light Negative Wire (-): Gray
Parking Light Negative Wire Location: At Headlight Switch (White 12-Pin Plug)
Parking Light Positive Wire (+): Gray
Parking Light Positive Wire Location: At Dash Fuse Box (18-Pin Plug)
Power Door Lock Negative Wire (-): Red
Power Door Lock Negative Wire Location: At Dash Fuse Box (24-Pin Plug)
Power Door Unlock Negative Wire (-): Light Green
Power Door Unlock Location: At Dash Fuse Box (24-Pin Plug)
Door Trigger Negative Wire (-): Brown
Door Trigger Negative Wire Location: At Dash Fuse Box (24-Pin Plug)
Dome Light Supervision Wire (+): Purple
Dome Light Supervision Wire Location: At Dash Fuse Box (24-Pin Plug)
Trunk Release Negative Wire (-): Blue
Trunk Release Negative Wire Location: At Dash Fuse Box (Green 52-Pin Plug)
Sliding Power Door Wire (-): N/A
Sliding Power Door Wire Location: N/A
Horn Negative Wire (-): Purple
Horn Negative Wire Location: At Horn Switch (20-Pin Plug)
Tachometer Wire Negative Wire (-): Green
Tachometer Wire Negative Wire Location: At Crankshaft Position Sensor (3-Pin Plug on the Engine Driver Side Rear)
Wait To Start Wire: N/A
Wait To Start Location: N/A
Brake Light Positive Wire (+): Light Green to Red
Brake Light Positive Wire Location: At Brake Light Switch (40-Pin Plug)
Factory Alarm Disarm Wire (-): Brown
Factory Alarm Disarm Wire Location: At Dash Fuse Box (24-Pin Plug)
Factory Anti-Theft System: Honda Transponder Anti-Theft System
Factory Anti-Theft System Location: Requires Key Bypass Module or Keyless Bypass Module

Thank you very much!
So i'm guessing that i should be looking for a 12V at the door area and connect the ground to the brown wire (DOOR TRIGGER)?

It's best to pull your 12v positive from a Battery feed and Fuse the 12v lead so you won't be overloading any circuits that you would try and connect too. .

I managed to find time today to install the scuff plates. To confirm, the Purple wire for Dome light supervision is a PURPLE / White one.

However, it seems that the current going through it is so small that it doesn't even trigger the relay that i was planning to use. I'm using a 30A relay with pins:

12V   = 86 & 85 as trigger
Ground= 30
NC = 87A
NO = 87

Any ideas?

If the scuff plates are LEDs you wont need a relay.
Having said that you wired the relay all wrong.
Purple to 86
Ground to 85
Power input 5 amp fused to 30
12V+ to lights at 87.
Ground to other side of lights.
Don't use 87a

-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.

Thanks for the reply. I wired it the same way as you mentioned. The post above was me trying hard (bad probably did a bad job) to explain the pin out of the relay i was using.

I tried to trigger the relay using the purple at 86, and ground at 85. I SHOULD hear a ticking sound, but it didn't occur. When i connected 86 to 12V, the ticking sound is heard.

Any idea why this is happening? Could it be that the current on the purple is too weak? When i tried to power the LEDs directly from the purple cable, the light was really weak. Or did i get the wrong purple cable :|

Try linking 30 to 86 and brown at dash fuse box (see above) to 85.

-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.