2000 Honda Accord Audio Wiring
Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=144784
Printed Date: April 27, 2024 at 3:09 PM
Topic: 2000 Honda Accord Audio Wiring
Posted By: shadydee2
Subject: 2000 Honda Accord Audio Wiring
Date Posted: September 29, 2018 at 6:48 AM
The stock audio wiring in a 2000 honda accord, specifically the speaker wiring from the harness to front speakers. Of the 2 wires one is a solid color , the other a solid color with a line of a different color running its length. Does that denote the wire being positive or negative?
-------------
daren obrecht
Replies:
Posted By: i am an idiot
Date Posted: September 29, 2018 at 6:12 PM
What are you trying to do?
Posted By: i am an idiot
Date Posted: September 29, 2018 at 6:18 PM
Left Front Speaker (+/-) blue/green - gray/black +,- radio harness
Right Front Speaker (+/-) red/green - brown/black +,- radio harness
Posted By: shadydee2
Date Posted: September 29, 2018 at 9:26 PM
Thank you. Now i have a bigger problem. As i was putting the speakers back in place(components 1 mid 1 tweeter) speaker wire from tweeter to crossover touched metal. Resulting in a high pitched hum like a ground loop. How do i get rid of.? Build has a isolated battery for 4 ch and mono block.
-------------
daren obrecht
Posted By: i am an idiot
Date Posted: September 29, 2018 at 9:53 PM
Is the noise only on that channel?
Posted By: shadydee2
Date Posted: September 30, 2018 at 9:26 AM
All 4. But not the mono block. Only the mids and highs. Hums constant meaning it does not increase or decrease when engaging the volume control on head unit. So it doesnt aeem to be a ground loop.
-------------
daren obrecht
Posted By: i am an idiot
Date Posted: September 30, 2018 at 10:45 AM
What kind of radio do you have in the dash? Does it have engine noise?
Posted By: shadydee2
Date Posted: September 30, 2018 at 2:43 PM
No. Its a kenwood ddx415bt that was in when it happened. I pulled it out and put in a kenwood dmx7704s and the hum stayed. A loud hum. Reminds me of when you put an electic guitar to close to your amp and get feedback from the pick ups. Except this is a steady and continuous hum. Ground loops normally change in pitch and in volume. As ive experienced anyways. Im seriously at a loss.
-------------
daren obrecht
Posted By: i am an idiot
Date Posted: September 30, 2018 at 3:09 PM
A grounded non bridged speaker wire can cause similar noises. Disconnect all 8 speaker wires from the amplifier, connect them 1 speaker at a time. Listen to it after each speaker connection. If that is not it, there is a good chance the amplifier has a problem since the wire touched.
Posted By: shadydee2
Date Posted: September 30, 2018 at 8:28 PM
Yeah its looking like even though no fuses blew. The jx 360 fusing is internal. Most likely i burned up the front end of the amp. I have a jl audio jx400/4d im going to put in and then ill know for sure. Thanks for your assistance as it is greatly appreciated.
-------------
daren obrecht
Posted By: i am an idiot
Date Posted: October 01, 2018 at 9:41 AM
Just an FYI, That amplifier is not internally fused. You must put a fuse inline with the power wire. JL recommends a 50 amp fuse.
The 400/4 is not internally fused either. They recommend a 40 amp fuse. This amplifier is Class D. It is more efficient than the Class A/B technology of the 360.
Posted By: shadydee2
Date Posted: October 01, 2018 at 1:13 PM
I said that wrong . I mesnt that there isnt any fuses to check on the outside of the amp. That also explains why i didnt see any bliwn fuses. I was using a 100 amp fuse..
-------------
daren obrecht
|