2011 Ford Expedition, Remote Start Wiring

Good afternoon. I am working on installing a remote start in my Expedition. I am installing a Avital 5305L with DB3. I looked for the wiring information under vehicle info but I could not find anything for this year. Yes I know there is a mod to use the factory remote start but I want to use a standalone system as I already had this one. Another thing is I would like to use the factory installed hood pin switch, does anyone know what the wiring colors are for this ? Any assistance in this matter would be greatly appreciated.

Here's the wiring:

EXPEDITION     2009-2014
KEY     T-HARNESS     IMMOBILIZER
FDKEY-4     N/A     FORDS TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1
PART     COLOR     LOCATION     DIAGRAM
12 VOLT CONSTANT     RED (+)     @ SJB, BLACK 1-PIN PLUG (G) Pin 1, Note #2     
STARTER     BLUE/WHITE (+)     @ IGNITION SWITCH, GRAY 10-PIN PLUG, Pin 10     
STARTER 2     N/A          
IGNITION 1     WHITE/ORANGE (+)     @ IGNITION SWITCH, GRAY 10-PIN PLUG, Pin 1     
IGNITION 2     N/A          
IGNITION 3     N/A          
ACCESSORY/HEATER BLOWER 1     BROWN/YELLOW (+)     @ IGNITION SWITCH, GRAY 10-PIN PLUG, Pin 7     
ACCESSORY/HEATER BLOWER 2     PURPLE/GREEN (+)     @ IGNITION SWITCH, GRAY 10-PIN PLUG, Pin 5     
KEYSENSE     N/A          
PARKING LIGHTS ( - )     Use Hazard Lights for (-) hook up GREEN/ORANGE     @ SJB BLACK 52 PIN PLUG(B) , PIN 48     
PARKING LIGHTS ( + )     PURPLE/WHITE (+)     @ SJB, GRAY 13-PIN PLUG(E), PIN 6, Note #2     
POWER LOCK     WHITE/BROWN (TYPE B)     in DRIVERS KICK PANEL or SJB, GRAY 26-PIN PLUG(C) Pin 17, Note #2     
POWER UNLOCK     BLUE/BROWN (TYPE B)     in DRIVERS KICK PANEL or SJB, GRAY 26-PIN PLUG(C) Pin 4, Note #2     
LOCK MOTOR WIRE     GRAY/BROWN ( 5-wire type)     in DRIVERS KICK PANEL or SJB, BLACK 32-PIN PLUG(D) Pin 6, Note #2     
DOOR TRIGGER     GRAY/PURPLE (+)     Connect positive (+) door trigger wire from alarm to dome light supervision on car     
DOMELIGHT SUPERVISION     GRAY/PURPLE (+)     @ SJB, GRAY 14-PIN PLUG(A) Pin 9, Note #2     
TRUNK RELEASE     BROWN (-) (Liftgate), BROWN/YELLOW (-) (Glass), Note #3     @ SJB, GRAY 26-PIN PLUG(C) Pins 7 and 20, Note #2     
SLIDING POWER DOOR     N/A          
HORN     YELLOW/RED (-)     @ HORN SWITCH or SJB, BLACK 52-PIN PLUG(B) Pin 41, Note #2     
TACH     Any wire NOT BLUE (AC)     @ Any FUEL INJECTOR     
WAIT TO START LIGHT     N/A          
BRAKE     YELLOW/GRAY (+)     @ BRAKE SWITCH or SJB, BLACK 52-PIN PLUG(B) Pin 40, Note #2     
FACTORY ALARM DISARM     N/A          
ANTI-THEFT     FORDS TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1     @ IGNITION SWITCH TUMBLER     
NOTES
NOTE #1: This vehicle is equipped with a Special Anti-theft key, to remote start you will need a Bypass module 791,(use this module IF you have a extra ignition key to place inside the 791 to remote start, if you do not have an extra key to use or wish not to have a key placed inside this bypass module, use Part # PKALL or PKFX, either one will work. If 2011-2014 and shaft of key has "SA" stamped into the metal this is Fords new 80bit key and will require a PKTX interface module

Note #2: The SJB, (Smart Junction Box) is located in the Passenger Kick Panel.

Note #3: TEST these wires while opening with the Handle on the Rear of the Vehicle. On vehicles with Power Liftgate the Open/Close wire is a GRAY/YELLOW (-) @ the Power Liftgate Switch on the Dash or in the DRIVERS KICK PANEL, Harness to Rear of Vehicle.

-------------
~wirewise~ Verify all wiring with your meter before making any connections!

This is awesome information. Thank you for this. I am still wondering if anyone has the wiring info for the factory hood switch that is next to the coolant reservoir. I want to hook my hood pin switch wire up to this since it is already in a good spot on the hood and it will help with a cleaner install.

I have installed alarms and remote starts in the past but I have never installed a bypass unit like the DB3. What all do I have to wire up from it to the car or the alarm remote start module? I know there is a data cable that goes between the DB3 and the Avital 5305 module.