Print Page | Close Window

Wiring Diagram for 2002 Chrysler Town and Country

Printed From: the12volt.com
Forum Name: Vehicle Wiring Information & File Requests
Forum Discription: Request Car Alarm, Car Stereo, Cruise Control, Remote Starter, Navigation, Mobile Video, and Other Vehicle Specific Wiring Info, Manuals, Tech Tips
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=1602
Printed Date: April 19, 2024 at 8:52 AM


Topic: Wiring Diagram for 2002 Chrysler Town and Country

Posted By: isaacl
Subject: Wiring Diagram for 2002 Chrysler Town and Country
Date Posted: June 29, 2002 at 10:50 PM

All,

I am looking for a wiring diagram (for an new alarm install) for a 2002 Town and Country minivan.  Mainly concerned about the power door lock interface.  What is the best easiest way to control the power door locks.

Thanks,

Isaac



-------------
isaacl



Replies:

Posted By: Velocity Motors
Date Posted: June 30, 2002 at 8:45 AM

Chrysler

Town & Country

2002

Remote Starter  Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Start:

 

 

YELLOW (READ NOTEs BELOW)

IGNITION SWITCH HARNESS *, **

Ignition  #1:

 

 

PINK/WHITE

IGNITION SWITCH HARNESS

Ignition #2:

 

 

N/A

Ignition  #3:

 

N/A

Accessory:

 

 

 

CHECK NOTES BELOW

Brake  Light:

 

 

WHITE/ BLACK

AT SWITCH ABOVE BRAKE PEDAL

Tach  Signal:

 

 

See Notes

Parking Lights:

 

 

RED / BLACK (+)

AT GREEN PLUG NEAR FUSE PANEL ***

Headlights:

 

 

OEM Alarm  Disarm:

 

VIOLET/LT. BLUE

AT PLUG AT PCM ON FIREWALL DRIVER'S SIDE ***

OEM Alarm  Arm:

 

VIOLET/LT. BLUE

AT PLUG AT PCM ON FIREWALL DRIVER'S SIDE ***

Diesel  Glow Plug:

 

N/A

Clutch  Bypass Wire:

 

N/A

Notes:

 * Many Of These Vehicles Are Equipped With A Transponder (Even If The Key Is Black)** NOTE!!! A Second Start Wire (PURPLE / Brown) Needs Ground (-) Through A 180 Ohm Resistor Is Required For Remote Start. *** The parking lights are negative trigger thru a 2.1K ohm resistor. The headlights are negative trigger thru a 790 ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch.TACH SIGNAL: On the 2.4L use blue/green or blue/tan. On the 3.3L/3.8L use blue/green, blue/tan or blue/orange. ACCESSORY : RUNS WITH IGNITION & A diode must be placed inline on this wire to avoid problems with the dome lights and parking lights.

Chrysler

Town & Country

2002

Alarm and Keyless  Entry Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Constant  +12 Volts:

 

 

RED

IGNITION SWITCH HARNESS (MAX 10 AMPS)

Starter  Kill:

 

YELLOW (READ NOTEs BELOW)

IGNITION SWITCH HARNESS *, **

Ignition  +12 Volts:

 

 

PINK/WHITE

IGNITION SWITCH HARNESS

Dome  Lights/Superv:

 

 

BLACK/ WHITE (-)

AT 4 PIN PLUG NEAR FUSE PANEL

OEM Horn:

 

 

GREEN/ BLACK (-)

STEERING COLUMN HARNESS

Power  Lock:

 

PURPLE / GREEN

AT PLUG AT PCM ON FIREWALL ****

Power  Unlock:

 

PURPLE / GREEN

AT PLUG AT PCM ON FIREWALL ****

Trunk  Release:

 

VIOLET/TAN

AT PLUG AT PCM ON FIREWALL DRIVER'S SIDE *****

Alarm  Input Wire:

 

BLACK/ WHITE (-)

AT 4 PIN PLUG NEAR FUSE PANEL

Notes:

. Green Wire. If Equipped With A Factory Alarm, Use The Above Note. ***** A Single Pulse Of Ground Through A 2.2 K-Ohm Resistor Will Open The Liftgate. POWER SLIDING DOORS: Violet/Dk. Blue Wire At Switch. Driver's Side - A Single Pulse Of Ground Through A 2.7 K-Ohm Resistor. Passenger's Side - A Single Pulse Of Ground Through A 1.5 K-Ohm Resistor.


-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA



Posted By: zorro33
Date Posted: December 07, 2002 at 4:47 AM
please help me i try to instal an aftermarquer jensen cm715k and i cannot put power to the amp(infinity)original.please,please,tell me the cable connectio .i have97 town and country.i can use the cable blu of the antena,,but where i connect in the original truck plug??????


Print Page | Close Window